background image

13

3 Year Guarantee

In the unlikely event of this product becoming faulty due to 
defective material or manufacture within 3 years of the date 
of purchase, please return it to your supplier in the first year 
with proof of purchase and it will be replaced free of charge. 
For the second and third years or any difficulty in the first year 
telephone the helpline on 

020 8450 0515

.

7. Specifications

Control Unit Supply voltage:  230V (+10%, -15%) 50Hz
Operating temperature:

 +5 to 40°C

Reserve battery:

Metal Hydride (rechargeable) 
PP3, 9Volt

Alarm Output:

 DC voltage through 470 ohm 
resistor. (Do not connect to 
mains voltage source)

Maximum pull force 
on pull cord:

200N

Reset button marking:

Visually and with Braille

Intensity of sounders:

Control Unit and Reset Units 
65dB at 30 cm
Over-Door Unit 78dB at 30 cm

Sound and light are intermittent
except Control Unit

Angular coverage of indicator: 180°on Over-Door Unit: 
EC directives:

Conforms to 73/23/EEC 
and 89/336/EEC

Dimensions: plastic (stainless steel)

Control Unit 

145 x 85 x 33, (145 x 85 x 35) mm

Pull cord Unit 

82 diameter x 20 mm

Overdoor Unit

85 x 85 x 24, (85 x 85 x 25) mm

Reset Unit 

85 x 85 x 12, (85 x 85 x 13) mm

Summary of Contents for EACP1

















Reviews: