background image

WARRANTY INFORMATION

Tiger Corporation, 3301 N. Louise, Sioux Falls, South Dakota, warrants to the

original Retail Customer, the new Tiger equipment is free of defects in material and
workmanship.   Any part of equipment that in Tiger’s judgement, show evidence of
such defects will be repaired or replaced without charge, provided that the failure of
part(s) shall have occurred within twelve (12) months from the date of delivery of
said equipment to the Retail Customer.   Expendable components such as knives,
oil, chain sprockets, skid shoes, knife mounting disks and the like are excluded but
not limited to this warranty.

The Retail Customer must pay the transportation cost to and from the Tiger

Dealer’s service shop for warranty service.   Warranty service will be performed by
the Tiger Dealer from whom the equipment was purchased, during service shop
regularly scheduled days and hours of operation.

All Tiger obligation under this warranty shall be terminated if the equipment is

modified or altered in ways not approved in writing by Tiger, if repair parts other than
genuine Tiger repair parts have been used, or if the equipment has been subject to
misuse, neglect, accident, improper maintenance or improper operation.

Tiger Corporation reserves the right to make improvements in design or

changes in specification at any time without incurring any obligation to owners of
equipment previously sold.

No agent or person has authority to alter, add to or waive the above warranties

which are agreed to be in the only warranties, representations or promises,
expressed or implied, as to the quality or performance of the products covered and
which do not include any implied warranty of merchantability or fitness.   In no event
will Tiger be liable for incidental or consequential damages or injuries, including, but
not limited to, loss of profits, rental or substitute equipment or other commercial
loss.

THERE ARE NO WARRANTIES WHICH EXTEND

BEYOND THOSE EXPRESSED HEREIN.

It is the 

Purchasers

 obligation to sign the warranty registration form 

AFTER

 he /

she has 

Read

 and 

Understands

 the 

Operation

 and 

Safety

 

Instructions

 stated

within this manual.

Summary of Contents for BENGAL JD6110-30M/R T4F



































































































































































































































Reviews: