manualshive.com logo in svg

Tiffen Steadicam M-2, System Manual, Page: 42 / 54

Share
Download
Tiffen Steadicam M-2 System Manual Download Page 42

42

Rear Electronics

On/Off and 12/24V switches

LEDs indicate 12/24V mode

5V USB power port

3rd Battery Port

Remove this cover to mount

Integrated wiring

Rear Battery (#1)

With 12V P-Tap

V-lock or Gold Mount

Clamp Knob

Secure the angle of batteries

Battery Rods

LWS 15mm by 60mm spacing

Industry-standard threaded ends

Front Battery (#2)

With 12V P-Tap

V-lock or Gold Mount

Front Electronics

High-definition video ports

Power ports

Base Connector

Modular mechanical and electronics junction

Indexed to ensure exact alignment with post

3rd Battery Switch

Choose 12V or 24V

when running 3rd battery

Battery Pivot

Adjustable friction

180˚ range

Clamp Levers

Lock or release the battery rods

NOTE: 

The base and battery mount section of this user guide covers product numbers M2-VLBASE and M2-GMBASE. For product 

numbers M1-VLBASE and M1-GMBASE, refer to the original M-1 manual (LIT-815000.)

Base and battery mount components

Summary of Contents for Steadicam M-2























































Reviews:

No comments