manualshive.com logo in svg

Tiffen Steadicam M-2, System Manual, Page: 39 / 54

Share
Download
Tiffen Steadicam M-2 System Manual Download Page 39

39

Loosen these eight hex screws to 

adjust the width. You may need to 

re-arrange the screws in different 

threaded holes, but use all eight.

Loosen the eight set screws to 

adjust the height of the uprights. 

Fit the monitor height so it clears 

the yoke when flipped 360˚.

Install your monitor:

•  Use supplied 1/4-20 screws to 

mount to monitors with 1/4-20 

side mounting holes.

•  Use 10-32 screws and supplied 

mounting block hardware that 

is monitor specific.

Use the markings to keep the 

monitor symmetrical side to side 

and on the uprights. Tighten all

of the screws.

Double check that the monitor is 

square to the rig, is held securely 

in the yoke, and rotates smoothly.

T

he universal monitor mount 

offers versatility and convenience to mount a variety of monitors near the 

monitor’s center of gravity, and allows tools free adjustment once it is fitted.

NOTE: 

Contact Tiffen for a selection of monitor blocks to fit your choice of professional monitor when 

upgrading or buying a spare.

TIP: 

The monitor can be offset left or right off center to help with view ability in some situations.

Monitor yoke adjustment

Summary of Contents for Steadicam M-2























































Reviews:

No comments