TIDELAND Nova-65 SC Operation Manual Download Page 16 | Manualshive

Page: 16 / 36

background image

MAINTENANCE AND OPERATION MANUAL

NOVA-65 SC/0111258-00

Tideland Signal

Page

12 of 32

0111258-00

Rev. B 16-Jun-16

Figure 8 On/Off/Winter Charging Switch

CAUTION!

Do not turn the lantern on inside a building. If the switch is

left in the On/Operate position inside a building, commercial lighting can
cause the solar panels to provide a high voltage, low current power to the
MaxiHalo II controller control circuit which may result in a microprocessor
malfunction. If the lantern does not operate, turning the switch to Off then
On should reset the microprocessor

2.2.3 Changing Flash Code

The flash code is fac

tory set to the customer’s specified code.

To change the flash code, refer to the Code Selection Guide enclosed in this
installation kit for switch settings. Remove the 5 screws securing the Nova-65
SC housing to access the MaxiHalo II controller control circuit. Two switches
are located on the control board, Switch 1 and Switch 2. Use your thumb and
index finger to rotate switches to desired locations.

«
...
14
15
16
17
18
...
»

Summary of Contents for Nova-65 SC





































Reviews:

No comments

Related manuals for Nova-65 SC

Brand: HAMPTON BAY Pages: 7

SXY81040CP-WW-P060

Brand: Clas Ohlson Pages: 5

Brand: GE Pages: 2

Brand: GE Pages: 2

LED Mariner Start

Brand: GE Pages: 7

Brand: GE Pages: 4

Brand: GE Pages: 2

Lumination LDXB Series

Brand: GE Pages: 11

Lumination LRC Series

Brand: GE Pages: 5

High Mast Luminaire

Brand: GE Pages: 2

Brand: GE Pages: 4

Lumination Current LEL Series

Brand: GE Pages: 3

Dome Top Decasphere

Brand: GE Pages: 2

Lumination BL44 Series

Brand: GE Pages: 4

Zoneline 1000 Series

Brand: GE Pages: 8

Lumination LPL GenB Series

Brand: GE Pages: 4

Brand: GE Pages: 4

Wallmount 175 Luminaire

Brand: GE Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands