THUNDER TIGER TITAN X50 -, Instruction Manual

Page: 21 / 54

-20-
Main Frame Assembly-7 /
本體組裝
-7
Bag H+K
No.
1
2
3
4
5
6
Qty Material No. Description
名稱
No.
7
8
9
10
11
12
13
Qty Material No. Description
名稱
Step 1 /
步驟一
Attach the Control Arms onto the Main Frame Set as drawing, and note the difference of
Left & Right Control Arms, please refer the “120L”/ “120R” mark on the arms.
參考圖示將控制搖臂裝上主側板上，請注意左、右邊的控制搖臂不同，請對照控制搖臂上L或R凸字
安裝。
(1) (2) (3)
(4)
(8)
(8) (7)
(4)
(4)
(6)
(3) (4)
(3)(2)
(1)
(7)
(3)
(5)
(4)
(12)
(9)
(10)
(13)
步驟二
1. 將3個固定環穿入尾管，並參考圖示平
均分配距離，然後再穿入尾管止擋環。
2. 將皮帶穿入尾管。將尾管推入尾管固定
座至底，請參考圖示，注意尾管上定位
凹槽方向。
3. 此時暫不需固定固定環及止擋環，以便
後續調整。
4. 安裝排氣管。
Step 2
1. Slide the 3 Tail Rod Guides onto the Tail Boom
and space them out evenly as drawing, and then
slide the Tail Boom Clamp onto Tail Boom.
2. Insert the Belt into the Tail Boom. Push the Tail
Boom in to the Tail Boom Bracket all the way to
the end. Refer the drawing and note the
orientation of slot on the Tail Boom.
3. Not fix the 3 Tail Rod Guides and not screw
tighten the Tail Boom Clamp at this step; the
position of these parts may be
adjusted later.
4. Attach the Muffler.
First tape the belt & insert the
end of the belt as shown, and not
twist the belt at this step.
使用膠帶將皮帶尾端貼合，會使皮帶
容易穿過尾管，並請勿扭轉皮帶。
Right side
右側
Left side
左側
This hole (Left & Right side both) is
design for 140°Control Arms(PV1409)
此孔位（左右二側）用於140°控制搖臂
（PV1409）
(10)
(11)
HMM3Z
NYLON NUT,M3
止鬆螺帽,M3
BK0077
COLLAR,d3xD4xW6
軸環,d3xD4xW6
HMV740ZZY
BEARING,d4xD7xW2.5
滾珠軸承,d4xD7xW2.5
BK0649-2
LINKAGE BALL(B)
內六角連接頭自攻螺絲(B)
HME3-30B
SET SCREW,M3x30
無頭內六角螺絲,M3x30
HMC3-10B
SOCKET SCREW,M3x10
內六角螺絲,M3x10
HMM3Z
BK0077
HMV740ZZY
BK0649-2
BK2160-R
BK2160-L BK2227
HME3-30B
BK0859-1
BK2559
HNN2-6B
BK2159
HMC3-10B
止鬆螺帽,M3
軸環,d3xD4xW6
滾珠軸承,d4xD7xW2.5
內六角連接頭自攻螺絲(B)
120° 控制搖臂(右)
120° 控制搖臂(左)
擺臂固定軸環
無頭內六角螺絲,M3x30
尾管,663mm
固定環
墊圈自攻螺絲,M2x3
尾管止檔環
內六角螺絲,M3x10
NYLON NUT,M3
COLLAR,d3xD4xW6
BEARING,d4xD7xW2.5
LINKAGE BALL(B)
120° CONTROL ARM-R
120° CONTROL ARM-L ARM COLLAR
SET SCREW,M3x30
TAIL BOOM,663mm
ROD GUIDE
TAPPING SCREW,M2x3
TAIL BOOM Clamp
SOCKET SCREW,M3x10
2
2
4
6
1
1
2
2
1
3
3
1
1
21mm
Must be purchased separately
改裝品需另購
All manuals and user guides at all-guides.com
all-guides.com