-6-
1
The signal directions of vary brand radios may differ, please read the GT5.1 instruction manual page 2 “Sensor Menu” to set the proper directions.
1
不同品牌遙控系統訊號方向會有所差異，請詳閱GT5.1說明書第2頁“陀螺儀設定”來設定正確的舵機作動方向。
1
3 systems of receiver may alternative: Standard Rx, Futaba S-bus or Spectrum Compatible, which depends on the radio system you use. Please refer
page 4 of this manual to know the correct device connections according to your radio brand.
2
Only used with Spectrum satellites; please refer your radio instruction manual if using a standard Rx or Futaba S-bus systems to execute binding.
To binding a Spectrum Tx and Rx: Activate the menu and both satellite LEDs will flash- placing the GT5.1 into “Bind” mode. Turn on the Tx whilst
holding in the bind-button. Binding is completed when the satellite LEDs remain solid.
1
依您所使用的接收機系統選用：標準接收機、Futaba S-Bus或Spectrum相容系統。並依所使用的遙控器品牌正確完成電子設備配線，說明請詳閱本說明書第4頁。
2
僅適用於Spectrum外接子天線；如使用標準接收機或Futaba S-bus系統，請翻閱您的遙控器說明書來執行對頻。
Spectrum對頻程序：進入本功能選單，此時子天線LED燈為快閃狀態，使GT5.1進入“對頻”模式。按住發射機上對頻功能鍵並開啟發射機電源，當子天線上LED
停止閃爍時，表示對頻完成。
■
Function
陀螺儀設定功能
Level 選單層
Default parameters
at Factory for E325S
E325S原廠設定值
Reset Default
重設預設值
1
1
2
Level 選單層
Default parameters
at Factory for E325S
E325S原廠設定值
Reset Default
重設預設值
1
2
Norm
Norm
Rev
Rev
Rev
Rev
Norm
Rev
Norm
5
2
Norm
5
2
■
Function
工具
Level 選單層
Default parameters
at Factory for E325S
E325S原廠設定值
Reset Default
重設預設值
1
1
2
Level 選單層
Default parameters
at Factory for E325S
E325S原廠設定值
Reset Default
重設預設值
1
2
2
25 Seconds
50 Seconds
■
Function
撥桿設定功能
Level 選單層
Default parameters
at Factory for E325S
E325S原廠設定值
Reset Default
重設預設值
1
2
Level 選單層
Default parameters
at Factory for E325S
E325S原廠設定值
Reset Default
重設預設值
1
2
25
25
0
0
25
25
0
0
25
0
0
10
25
0
0
10
Functions for sensor calibrations,
DO NOT touch these values.
工程用途，請勿更動。
Standard Rx
DX7
Refer the GT5.1 and your radio instruction
manuals to learn how to binding.
請參閱GT5.1及遙控器說明書完成對頻。
Recover “Reset Default” parameters
重設為預設值
No function as yet and should not be used.
功能保留，無需設定
To set the Fail-Safe function on your helicopter as well for safety is strongly recommended. Please refer your radio
instruction manual to learn how to set the FS function if using a Standard Rx or Futaba S-bus. If using a Spectrum
compatible Rx, please refer the page 2 of GT5.1 manual “Fail-safe Configuration upon DSM2/X”.
安全起見，強烈建議您也同時設定“安全回復”功能。如使用標準接收機或Futaba S-bus系統，請翻閱您的遙控器說明書來完成設定
。如您使用Spectrum相容系統，請詳閱GT5.1說明書第2頁“DSM2/X系統安全回復設定”。
1
The signal directions of vary brand radios may differ, please refer your transmitter instruction manual and page 7 of this manual “SWASHPLATE &
SERVO MOVEMENT SETTING” to set the proper directions.
2
The values on this function depends on the specifications of the servos you purchase, any wrong value set here may cause unexpected damage of
servos, please inquire the servo manufacture to know the specification in details.(The values here had already pre-set properly at factory for the
servos come with E325S.)
1
不同品牌遙控系統訊號方向會有所差異，請參考您的遙控器說明書及本說明書第7頁“十字盤及伺服機動作設定”來設定正確的舵機作動方向。
2
本功能內設定值取決於您所使用的舵機規格，任何錯誤設定值都可能造成舵機損壞，敬請向舵機製造商詢問詳細的規格數據。（該值已由原廠針對E325S所附舵機
正確設定完成。）
