Thonk Eurorack DIY Kit Instructions Manual Download | Manualshive

Page: 5 / 17

background image

December 14th 2018

www.thonk.co.uk

5

PROK DRUMS

Eurorack DIY Kit

Instructions

Version 1

7.

Next  locate  the  SMD  voltage
regulator  which  is  packaged  as
shown.

Do  not  remove  it  from  its
packaging  yet  -  complete  the
next step first.

8.

Next locate the position for the
SMD regulator on the PCB as
shown.

9.

Now heat the single pad next to
the text ‘IC1’ with your soldering
iron,  and  once  heated  add  a
small  blob  of  solder  –  just
enough  to  cover  the  entire  pad
as shown.

«
...
3
4
5
6
7
...
»

Summary of Contents for Eurorack DIY Kit


















Reviews:

No comments

Related manuals for Eurorack DIY Kit

Future Impact I

Brand: Panda-Audio Pages: 2

KOSMODROM CORE v 1.2 PCB SET

Brand: Tsyklon Labs Pages: 16

Brand: Bastl Instruments Pages: 16

Brand: Sequential Pages: 115

Brand: Sequential Pages: 168

Brand: Sanchez Pages: 53

Brand: EKSSPERIMENTAL SOUNDS STUDIO Pages: 11

Brand: Yamaha Pages: 22

Gotharman’s Anamono

Brand: Gotharman Pages: 3

Brand: Roland Pages: 10

Brand: Roland Pages: 18

Phase Lab MC-09

Brand: Roland Pages: 21

Brand: Roland Pages: 24

Orchestra M-OC1

Brand: Roland Pages: 38

Brand: Roland Pages: 44

PhraseLab MC-09

Brand: Roland Pages: 88

Sound Canvas SC-50

Brand: Roland Pages: 112

Sound Canvas SC-88 VL

Brand: Roland Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands