Thonk Eurorack DIY Kit Instructions Manual Download Page 3 | Manualshive

Page: 3 / 17

background image

December 14th 2018

www.thonk.co.uk

3

PROK DRUMS

Eurorack DIY Kit

Instructions

Version 1

PROK DRUMS BUILD INSTRUCTIONS

1.

There are two PCBs used in this
build - they are referred to as the
front  PCB  and  the  back  PCB.
They  can  be  identified  by
locating the text on each PCB as
shown.

BACK BOARD

2.

We will start with the back PCB.

All  the  parts  for  this  PCB  are
located  in  a  labelled  bag  within
the main kit bag. Empty this bag
into  a  bowl  or  container  –  all
other parts can be put to the side
for  the  moment  except  for  the
Teensy.

«
1
2
3
4
5
...
»

Summary of Contents for Eurorack DIY Kit


















Reviews:

No comments

Related manuals for Eurorack DIY Kit

Brand: Yamaha Pages: 19

Brand: BugBrand Pages: 2

Brand: Studiologic Pages: 27

Brand: Gakken Pages: 4

Brand: Roland Pages: 52

Brand: Kaino Pages: 23

Brand: TB-Electronics Pages: 30

Brand: Dave Smith Instruments Pages: 96

Brand: twisted electrons Pages: 21

Brand: Plankton Electronics Pages: 10

Brand: Jomox Pages: 37

Brand: Jomox Pages: 120

Gotharman's anAmoNo-box

Brand: Gotharman Pages: 9

SpazeDrum Black

Brand: Gotharman Pages: 11

Gotharman's SpazeDrum

Brand: Gotharman Pages: 14

Brand: Gotharman Pages: 20

Brand: Gotharman Pages: 73

Brand: Gotharman Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands