Thonk Eurorack DIY Kit Instructions Manual Download Page 13 | Manualshive

Page: 13 / 17

background image

December 14th 2018

www.thonk.co.uk

13

PROK DRUMS

Eurorack DIY Kit

Instructions

Version 1

33.

Next solder in the two BAT42
diodes into D7 and D8 as shown.

NOTE:

Take care with the

orientation  of  the  black  stripes
on  the  diodes  –  these  should
match  the  black  stripes  on  the
PCB silkscreen.

NOTE:

Do not heat the diodes

excessively or you will damage
them, you should be aiming to
solder quickly and neatly.

34.

Next solder in the single 100n
capacitor into C1.

35.

Next  we  will  solder  the  four
standing  resistors  starting  with
single remaining 1.5K resistor.

Bend the resistor lead as shown
to  prepare  it  to  stand  on  the
PCB, then place it into the PCB
at R13 with the bent lead facing
the PCB edge as shown.

36.

Now solder the standing 1.5K
resistor into R13.

«
...
11
12
13
14
15
...
»

Summary of Contents for Eurorack DIY Kit


















Reviews:

No comments

Related manuals for Eurorack DIY Kit

Brand: Oberheim Pages: 90

Brand: Alesis Pages: 48

Brand: Hameg Pages: 40

Brand: Sequential Pages: 120

DarkStar Vocoda

Brand: Red Sound System Pages: 24

Brand: CHD Pages: 32

soundhack ECHOPHON

Brand: Make Noise Pages: 10

Brand: Xaoc Devices Pages: 8

Brand: Shift Line Pages: 2

Harmony Director HD-300

Brand: Yamaha Pages: 2

Spectrum Bass II

Brand: Peavey Pages: 39

Brand: Peavey Pages: 44

Brand: ADDAC System Pages: 8

12-61 Black Edition

Brand: Miditech Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands