Thonk Eurorack DIY Kit Instructions Manual Download Page 4 | Manualshive

Page: 4 / 17

background image

December 14th 2018

www.thonk.co.uk

4

PROK DRUMS

Eurorack DIY Kit

Instructions

Version 1

3.

Start by soldering the single 5.6K
resistor into the position labelled
R4 as shown.

4.

Next solder the single 39K
resistor into position R3.

5.

Next solder the three 56K
resistor into positions R5, R6
and R7.

6.

Next solder the two 1N5819
diodes into position as shown.

NOTE:

Take care with the

orientation of the grey stripes on
the diodes – these should match
the black stripes on the PCB
silkscreen.

NOTE:

Do not heat the diodes

excessively or you will damage
them, you should be aiming to
solder quickly and neatly.

«
...
2
3
4
5
6
...
»

Summary of Contents for Eurorack DIY Kit


















Reviews:

No comments

Related manuals for Eurorack DIY Kit

Brand: Oberheim Pages: 4

Brand: Valon Pages: 2

Brand: Roland Pages: 10

Brand: Sequential Pages: 93

Brand: Holzworth Instrumentation Pages: 68

Brand: Sequential Pages: 17

Brand: Sequential Pages: 54

Brand: Sequential Pages: 48

Clavinova CVP-609

Brand: Yamaha Pages: 117

Brand: Yamaha Pages: 66

Brand: Kawai Pages: 48

Brand: Keithley Pages: 64

Brand: Yamaha Pages: 93

ENVELOPE FOLLOWER / PREAMP

Brand: SPUTNIK MODULAR Pages: 7

Brand: nord Pages: 233

Analog Four MKII

Brand: Elektron Pages: 108

Brand: Elektron Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands