THOMSON TG790 Setup And User Manual Download

Page: 31 / 78

E-DOC-CTC-20080118-0075 v1.0

Adding New Devices to your Network

3.2.2

Configuring your Thomson Gateway

Introduction

If you configured your Thomson Gateway using the

Guided Installation

, the telephony service will already be

configured by the Setup wizard.

If you choose to configure your Thomson Gateway manually or you still need to configure the telephony
service, you can follow the procedure below.

Procedure

Proceed as follows:

Enable the Telephony Service

Assign Phone Numbers

Configure the Telephony Service

Enable the Telephony Service

To enable the telephony service:

Browse to the

Thomson Gateway Web Interface

On the

Toolbox

menu, click

Telephony.

In the

Navigation Bar

, click

Configure

Select

Service Enabled

Click

Apply

Assign Phone Numbers

To configure your Internet SIP telephone numbers:

Browse to the

Thomson Gateway Web Interface

On the

Toolbox

menu, click

Telephony

In the

Navigation Bar

, click

Configure

. Assign phone numbers to the ports. If you want to use the same

number for all ports, select Port ‘

All

’.

Click

Apply

Configure the Telephony Service

Proceed as follows to configure the telephony service:

Browse to the

Thomson Gateway Web Interface

On the

Toolbox

menu, click

Telephony

In the

Navigation Bar

, click

Expert configure

Your Internet connection must be up and running before you can configure Internet telephony.

The phone numbers are provided by your provider.

Summary of Contents for TG790














































































Search results

Summary of Contents for TG790

Reviews:

Related manuals for TG790

Brands by name

Popular brands

THOMSON TG790, Setup And User Manual

Search results

Summary of Contents for TG790

Reviews:

Related manuals for TG790

Brands by name

Popular brands