background image

SERVICE AND MAINTENANCE 
 

24 

 

7.1.2.

 

Cleaning the chimney box 

To ensure efficient and safe function of the boiler, you must 
clean the chimney box  from ash residues 

at  least  every  3 

months. 

The  ash  box  is  equipped  with  a  cleaning  door  for  this 
purpose,  as  shown  in  Fig  14.  In  order  to  open  the  door, 
unscrew the wing nuts, remove the washers and springs that 
keep it in place.  

Clean the interior of the chimney box and remove all the ash 
and residues.  

Put back the door the same way as removed.  

 The  springs  must  not  be  omitted!  They  act  as 

safety  in  order  of  explosion  of  exhaust  gases  in  the 
chimney box. 

 

Fig 14.

 

Cleaning the chimney box 

 

7.1.3.

 

Cleaning the furnace 

The furnace should be regularly cleaned according to the ash deposits, but not less than once a 
week. To clean the furnace follow the next steps:  

 

Stop the furnace function by the control panel and leave it to cool down completely. 

 

Clean  the  surface  of  the  cast  iron  plate  from  ashes  and  other  deposits.  Make  sure  the  air 
holes are clean and free from obstacles.  

 

Clean the ashes and deposits at the perimeter around the plate. 

 

After you turn on again the furnace, ensure the fuel feeding is performed freely and the fuel 
is evenly distributed at the plate surface.   

 

Check the function of the motoreducer and the fan. Clean from dust if needed.  

 

7.2.

 

Maintenance intervals 

7.2.1.

 

Daily maintenance 

The pressure of the network must be daily verified to be within the allowed limits. Make sure 
that all the safety devices and pumps function properly.  

7.2.2.

 

Weekly maintenance 

The  boiler  must  be  cleaned  every  3-4  days  or  at  least  once  a  week,  depending  on  the  ash 
quantity accumulated on the boiler walls and in the heat exchanger. Cleaning procedure must 
be performed according to the instruction given in the corresponding paragraph.  

Check  the  quantity  of  ash  accumulated  in  the  ash  box.  The  ash  disposal  can  be  performed 
every 1-2 weeks, depending on the ash quantity formed.  

7.2.3.

 

Monthly maintenance 

Check the doors and the sealing cord. Make sure the contact with the boiler is air-tight. If ash 
has accumulated on the sealing cord, clean it.  

Check  the  fan  and  make  sure  it  functions  properly.  Clean  from  dust  and  check  that  the  air 
passage is clear of obstacles and dust.  

Remove the turbinators from the heat exchanger and check their condition. 

It is recommended that you clean the chimney box of the boiler and the chimney pipes at least 
every 3-4 months, in order to assure efficient and safe function of the boiler.    

Summary of Contents for BIOPLEX MCL-BIO

































Reviews: