Page 43
e manutenzione
Maximum number of elbows at least 0.5 m apart: 2
• The appliance door must always remain closed during normal operation.
• Do not touch hot outer surfaces, unless with special equipment.
• Do not pour the pellets directly into the brazier.
• Keep fuel and inflammable materials at a suitable distance.
• Use only original spare parts supplied by the manufacturer.
12.3 TROUBLESHOOTING CAUSE-SOLUTION
PROBLEM
CAUSE
SOLUTION
PELLET TANK IS EMPTY
(DISPLAY SHOWS THE INSCRIPTION “AL PE”)
EMPTY THE BURNER AND CLEAN IT UP AS INDICATED IN
PARA. 8
THEN FILL UP THE TANK WITH PELLETS
FEEDER SCREW BLOCKED BY FOREIGN OBJECT SUCH AS
NAIL, NYLON, PIECE OF WOOD
REMOVE THE FOREIGN OBJECT INSIDE THE TANK.
(DISPLAY SHOWS THE INSCRIPTION “AL PE”)
CUT OFF THE POWER AND REMOVE THE FOREIGN
OBJECT.
SMOKE EXHAUST NOT FREE, OR WITH TERMINAL THAT
OBSTRUCTS THE PASSAGE OF SMOKE
(DISPLAY SHOWS THE INSCRIPTION “AL OP”)
EMPTY THE BURNER AND CLEAN IT UP AS INDICATED IN
PARA. 8.
THEN CHECK THE SMOKE EXHAUST AS IT COULD BE
DIRTY OR CLOGGED
OUTLET TERMINAL CLOGGED BECAUSE A GRILL OR
TERMINAL HAS BEEN INSERTED WHICH PREVENTS THE
FREE PASSAGE OF SMOKE
(DISPLAY SHOWS THE INSCRIPTION “AL OP”)
EMPTY THE BURNER AND CLEAN IT UP AS INDICATED IN
PARA. 8.
THEN REMOVE THE TERMINAL AND REPLACE IT WITH A
MORE SUITABLE ONE.
GUST OF WIND WHICH HAS MADE THE APPLIANCE GO INTO
SAFETY MODE
(DISPLAY SHOWS THE INSCRIPTION AL OP)
EMPTY THE BURNER AND CLEAN IT UP (SEE PARA. 8)
SWITCH THE POWER SUPPLY TO THE APPLIANCE OFF
THEN BACK ON AGAIN
THE PELLET SCREW MOTOR DOES NOT WORK
REPLACE THE PELLETS SCREW MOTOR
PELLETS DO NOT DROP INTO THE
BURNER
THE RESET THERMOSTAT TRIPS AND LOCKS THE
GEARMOTOR
(DISPLAY SHOWS THE INSCRIPTION AL T max )
THE ROOM FAN IS DAMAGED AND MUST BE REPLACED.
WAIT UNTIL THE APPLIANCE COOLS DOWN AND PUT
BACK INTO SERVICE THE RESET THERMOSTAT.
SMOKE EXHAUST NOT FREE, OR WITH TERMINAL THAT
OBSTRUCTS THE PASSAGE OF SMOKE
EMPTY THE BURNER AND CLEAN IT UP AS INDICATED IN
PARA. 8.
THEN REMOVE THE TERMINAL AND REPLACE IT WITH A
MORE SUITABLE ONE.
THEN CHECK THE SMOKE EXHAUST AS IT COULD BE
DIRTY OR CLOGGED
BURNER IS DIRTY
EMPTY THE BURNER AND CLEAN IT UP AS INDICATED IN
PARA. 8.
THE DOOR IS NOT FIRMLY CLOSED / WORN GASKET
CLOSE THE DOOR FIRMLY / REPLACE THE GASKET
EMPTY THE BURNER AND CLEAN IT UP AS INDICATED IN
PARA. 8.
EMPTY THE BURNER AND CLEAN IT UP AS INDICATED IN
PARA. 8.2. THEN SET THE OPERATING PROGRAM Level 2
PELLETS WITH DEPOSIT ABOVE PERMISSBILE LIMITS
EMPTY THE BURNER AND CLEAN IT UP AS INDICATED IN
PARA. 8.
CHANGE THE TYPE OF PELLETS
THE APPLIANCE ACCUMULATES
PELLETS IN THE BRAZIER WHILE
OPERATING
THE BURNER IS NOT PROPERLY PLACED ON ITS SEAT OR IT
STAYS LIFTED FROM ITS SEAT
EMPTY THE BURNER AND CLEAN IT UP AS INDICATED IN
PARA. 8.
THEN SET THE BURNER ON ITS SEAT PROPERLY
OCCURS THE FIRST TIME THE APPLIANCE IS SWITCHED ON
AS THE SILICONE PAINT IS BEING BAKED.
RUN THE APPLIANCE AT FULL POWER FOR 10 HOURS TO
COMPLETE THE BAKING.
THE SMOKE EXHAUST IS NOT SEALED CORRECTLY
CHECK IF THE FLUE OUTLET IS SEALED CORRECTLY
CHECK THE CONDITION OF THE OUTLET TUBES AND IF
THE GASKETS ARE SEALED CORRECTLY
IF THE APPLIANCE STARTS TO SMOKE AFTER 25 MINUTES:
DIRTY BURNER, VERY DELAYED START
EMPTY THE BURNER AND CLEAN IT UP AS INDICATED IN
PARA. 8.
IF THE APPLIANCE STARTS TO SMOKE AFTER 25 MINUTES:
DELAYED START BECAUSE THE SCREW FEEDER IS EMPTY
EMPTY THE BURNER AND CLEAN IT UP AS INDICATED IN
PARA. 8.
THEN FILL UP THE TANK
THE APPLIANCE SMOKES
SMOKE PURGE VALVE TRIPPING
FOLLOW ALL THE CLEANING AND MAINTENANCE
INSTRUCTIONS SET OUT IN PARA 8, INCLUDING THE
CLEANING OF THE FLUE OUTLET
DELAYED START BECAUSE THE SCREW FEEDER IS EMPTY
(DISPLAY SHOWS THE INSCRIPTION AL AC)
EMPTY THE BURNER AND CLEAN IT UP AS INDICATED IN
PARA. 8.
THEN FILL UP THE TANK
THE APPLIANCE SHUTS OFF A FEW
MINUTES AFTER THE END OF THE
START UP CYCLE
DIRTY BURNER, VERY DELAYED START
(DISPLAY SHOWS THE INSCRIPTION AL AC)
EMPTY THE BURNER AND CLEAN IT UP AS INDICATED IN
PARA. 8.
THEN FILL UP THE TANK
Summary of Contents for DORICA MAIOLICA
