Page 39
e manutenzione
9.3.3 CONTROLS PRIOR TO INSTALLING THE
APPLIANCE
The user must possess a certificate of
conformance for the flue outlet (Ministerial Decree
22 January 2008, no. 37).
The flue outlet must be built in compliance with
UNI 10683.
•The smoke exhaust shown in the following
figures is the best solution to ensure the
discharge of smoke even when the fan is not
operational, such as for example if there is an
electrical power failure. A minimum drop of 1.5
metres is required between the T terminal on the
outside of the building and the outlet at the back
of the appliance, to ensure that residual
combustion smoke is discharged in the case
described above (otherwise the residues would
stagnate inside the firebox and exhaust into the
environment with added the possibility of
explosions). The figures illustrate the best solution
for discharging the smoke out through the roof or
into the flue outlet.
If you prefer to exhaust the smoke from the roof
insert a union tee with inspection cap, connecting
brackets suitable for the height of the flue outlet,
flashing that crosses the roof and chimney cap to
protect against bad weather conditions. If you
decide to use the classic masonry exhaust
provide a union tee with inspection cap and
suitable supporting brackets. If the flue outlet is
too big it is necessary to insert a stainless steel or
porcelain-coated steel tube with a diameter not
exceeding 150mm. Seal area where the inlet and
outlet part of the smoke exhaust meets the wall. It
is strictly forbidden to apply mesh to the end of
the outlet tube, as it could cause the appliance to
malfunction.
LEGENDA
KEY
COMIGNOLO E CANNA FUMARIA
SECONDO NORMA UNI 10683
CHIMNEY CAP AND FLUE OUTLET
ACCORDING
TO
UNI
10683
STANDARD
2 metri MAX.
2 metres MAX.
Pendenza non inferiore al 5%
Minimum slope 5%
Ispezione
INSPECTION
Tutte le tubazioni devono essere
termicamente isolate
All the pipes must be thermally
insulated
ALTEZZA SUPERIORE A 4metri
HEIGHT MORE THAN 4m
2-3 metri MAX
2-3 metres MAX.
ISPEZIONE
INSPECTION
If the smoke tube is installed in a fixed position it
is advisable to provide inspection openings for
clean-out purposes especially in the horizontal
sections. See the diagram. These openings are
essential to allow for the removal of ash and
unburned products which tend to accumulate
along the discharge path.
The appliance operates with the pressure in the
combustion chamber lower than atmospheric
pressure, whereas the discharge of smoke to the
chimney is slightly pressured, consequently the
discharge system must be hermetically sealed.
The smoke discharge tube must be made from
suitable materials such as for example:
INTERNO – ESTERNO
INNER - OUTER
porcelain-coated steel tubes, and the various fittings sealed with red silicone (resistant to 350°C). The outer casing of the tube must
be made with insulating material (mineral wool, ceramic fiber) or use pre-insulated tubing.
THE FLUE OUTLET MUST BE USED ONLY FOR THE APPLIANCE .
ISPEZIONE
2
-
3
m
e
tr
i
M
A
X
.
ISPEZIONE
ISPEZIONE
2 metri MAX
.
Pendenza n
on inferiore a
l 5 %
A
L
T
E
Z
Z
A
S
U
P
E
R
IO
R
E
A
4
m
e
tr
i
C
O
M
IG
N
O
L
O
E
C
A
N
N
A
F
U
M
A
R
IA
S
E
C
O
N
D
O
N
O
R
M
A
U
N
I
1
0
6
8
3
Tutte le tubazioni devono
essere termicamente isolate.
Summary of Contents for DORICA MAIOLICA
