SET
TO-712F
1. DESCRIPTION
2. MAIN APPLICATIONS
3. TECHNICAL SPECIFICATIONS
4. INTRODUCTION
Quick touch:
Increases
parameter value when in
programming mode;
U p p e r d i s p l a y :
I n d i c a t e s t h e
temperature measured by the sensor or
parameter configuration;
Lower display:
Indicates the cooking time
or parameter configuration;
Temperature units indicator
led;
Quick touch:
Temperature
and cooking time adjustment;
Long touch:
Access to the
advanced configuration;
Quick touch:
On /off lamp output.
Quick touch:
Decreases
parameter value when in
programming mode;
Quick touch:
Steam activation;
Long touch:
Steam activation time adjustment;
Quick touch:
Timer activation;
Functions lock indication led;
Led lamp output indicator
led;
Steam output on
indication led;
T i m e r a c t i v a t e d
indication led;
Heating on indication led;
Ignition output switched on;
SET
Each key has a led to indicate its function. When the
led is on, it indicates that the key is active and can be
pressed.
KEY FUNCTIONS
Electric power supply
85~265Vca (50-60Hz)
Operating temperature
0 to 60ºC
Control temperature
-10 to 500ºC / 14 to 932ºF
Operating humidity
10 to 90% UR (without condensation)
Temperature sensor
Type J thermocouple (sold separately)
Resolution
1ºC / 1ºF
Digital Input
E1: door micro switch input
Flame sensor
E2: flame sensor input
Relay outputs
Product dimensions (mm)
75 x 75 x 100 (WxHxD)
Opening dimensions (mm)
67,2 x 67,2
T
O712FV01-02B-15939
TEMPERATURE AND TIME
CONTROLLER FOR OVENS
TO-712F
Ver.01
Heating
Buzzer
Steam
Lighting
Functions
lock
Serial
programming
Protection
level
IP 65
FRONT
Timer
Thermostat and timer for the automation of forced convection ovens. This model provides control over gas, electric, or wood
powered ovens, configured through the setup menu.
TO-712F
controls steam injection and lighting in the oven, and has an
internal audible alarm (buzzer) that signals, for example, the end of the roasting process. It also allows for the use of an
external audible alarm and the language selection of your main messages, improving the user experience. The ThermON
line is developed and produced with high-quality raw materials and stands out for its unique and differentiated design and
intuitive, user-friendly interface to facilitate operation and configuration. It offers a functions lock feature to prevent third
parties from changing the parameters, air-tight front panel that provides high protection against the entry of dirt and moisture,
and more.
BEFORE INSTALLING THE CONTROLLER, WE RECOMMEND READING THE INSTRUCTION MANUAL IN FULL TO PREVENT
POSSIBLE DAMAGE TO THE PRODUCT.
THROUGH CONTINUOUS DEVELOPMENT, FULL GAUGE CONTROLS RESERVES THE RIGHT TO CHANGE THIS MANUAL
INFORMATION AT ANY TIME, WITHOUT PRIOR NOTICE.
Baking ovens, stoves;
SET
KEY
LED
4 relay outputs: 5 (3)A / 250Vac 1/8HP
External audible alarm (buzzer) output
12Vcc/30mA (max)
Approximate consumption 10VA
IN THIS OPERATING MODE THE FLAME SENSOR IS IGNORED AND THE CONTROLLER WILL NOT DETECT
THE PRESENCE/LACK OF FLAME, BEING ESSENTIAL FOR THE OPERATOR TO PAY SPECIAL ATTENTION
TO CONTROL THE OVEN IN ORDER TO PREVENT GAS ACCIDENTS.
SET
SET
SET
Use the
<
or
>
keys to select the desired function. The value can be edited with a quick touch on the key. Use the
<
or
>
keys to change the value and press the key with a quick touch when ready to save the configured value and return to the
functions menu. To leave the configuration menu and return to the normal operating mode (temperature indication), press
(long touch) until
[----]
is displayed.
SET
Access the menu setting by pressing the key for 4 seconds until
[Func]
is displayed. When
[CoD]
is
displayed press the key again (quick touch). Use the
<
or
>
keys to enter the access code 231 and
press (quick touch) again when ready.
SET
SET
Temperature units selection
Selects the temperature units the controller will
use for its operation.
[i03]
ºC
ºF
-
°C
Language selection
Selects the language the controller will use to
display messages:
[Port]
= Portuguese
[,EnG]
= English
[,ESP]
= Spanish
[i04]
PORT ESP
-
PORT
Enable external audible alarm
(buzzer)
Enables or disables the external audible alarm
(buzzer). If enabled, the internal audible alarm
(buzzer) will be disabled.
[i05]
OFF
ON
-
OFF
DESCRIPTION
FUN
MIN
MAX
UNIT
DEF.
FUNCTION
5.1Installation setup table
Access code (231)
Required when you want to change installation
setup parameters.
[CoD]
0
9999
-
Temperature sensor type
Defines the type of temperature sensor to be
used with the controller.
[i02]
J
J
-
0
J
Oven type selection
Selects the control type of the oven:
[ELE,]
= Electric oven
[GAS,]
= Gas-fired oven
[LEN,]
=
Wood-fired oven
[i01]
ELE
LEN
-
GAS
Door digital input signal type
[,NO,]
- normally open contact (NO)
[,NC,]
- normally closed contact (NC)
[i07]
NO
NC
-
NO
[i06]
Internal audible alarm (buzzer)
volume
Selects the sound intensity of the internal
audible alarm (buzzer).
[Min,]
= low volume
[Med,]
= medium volume
[HiGh]
= high volume
MIN
HIGH
-
MED
IMPORTANT:
This function is not available
for this model.
6.1 Oven: Electric
In this operating mode the controller keeps the heating output on until the oven reaches the oven temperature setpoint (SP). The
output will be activated again when the temperature drops below the setpoint minus the hysteresis (F04).
6.2 Oven: Gas
In this operating mode the controller automates / monitors the flame ignition and thus the heating of the oven through the
activation of the gas output, ignition module, and flame sensor input. The controller keeps the heating output on until the oven
reaches the oven temperature setpoint (SP). Heating will be activated again when the temperature drops below the setpoint
minus the Hysteresis (F04). The controller permanently monitors the flame sensor to ensure the safe operation of the gas-fired
oven. In this way, if there are any abnormalities, errors Er4 - Flame Sensor shorted with the burner and Er5 - Lack of Flame are
indicated. For more information check item 9 (Signaling).
6.3 Oven: Wood
In this operating mode the heating output works as an upper threshold alarm, indicating when the temperature exceeds the value
adjusted in Oven Temperature setpoint (SP). The audible alarm is also activated to warn the user about the overheating. The
output and audible alarm are switched off when the temperature drops below the Oven Temperature setpoint (SP) minus the
Hysteresis (F05) or when a key in the controller's front panel is pressed.
6.4 Default Mode (standard)
In this operating mode the controller performs the gas type control, however the flame sensor is ignored and the controller will not
monitor flame presence. The controller will not detect errors Er4 - shorted flame sensor and Er5 - out of gas, resulting in an
operation with less safety.
NOTE:
The Default Mode (standard) of operation is available only when the type of oven is adjusted as gas. To execute this
operating mode, check item 5.5 Enable Default (standard) Mode of operation.
6. OPERATION
5.
INSTALLATION CONFIGURATION
The controller has easy access to resources that are relevant to the user of the oven.
7.1 Adjustment of oven temperature and timer
To adjust oven temperature and timer, perform a quick touch on the
key. Use the
<
or
>
keys to adjust the value of
the parameter. To advance and/or terminate the adjustment, perform another quick touch on the key.
ADJUSTMENT OF THE DESIRED TEMPERATURE (SETPOINT) OF THE OVEN:
Defines the working temperature of the oven. This parameter can be adjusted between the values
defined in F02 - Minimum value allowed to configure the oven temperature setpoint and F03 - Maximum
value allowed to configure the oven temperature setpoint.
TIMER SETTINGS:
Defines the cooking time. When the time expires, the audible alarm output is switched on intermittently
until any key on the controller's front panel is pressed. The timer can be adjusted between 00:01 and
99:59. The time scale is adjusted in parameter F14 - Time base of the timer.
7.2 Steam activation
The steam operating mode is defined in parameter F18 - Steam Operating Mode. Steam activation depends on
parameters F20 - Time interval between steam activations and F21 - Minimum temperature to activate the steam,
available in the advanced configuration menu. These conditions must be met for the injection of steam in the oven to occur.
7.2.1 Steam activation times
Press the
%
key and hold for 4 seconds to adjust. Use the
<
or
>
keys to adjust the value. To confirm, perform a quick
touch on the
%
key.
STEAM OUTPUT ON TIME:
This parameter can be adjusted between 1 and 30 seconds, and the factory default is 5 seconds.
STEAM OUTPUT OFF TIME:
This parameter can be adjusted between 1 and 600 minutes, and the factory default is 3 minutes.
NOTE:
This parameter is available for adjustment when the steam control mode selected is cyclic,
[F18]
=
[CYC,]
.
7.3 Functions lock
To enable the Default (standard) operating mode of the oven, the controller must be powered up with the
$
and
%
keys pressed until the message appears on the display. This mode is available when the
type of oven selected is GAS. For more details about this operating mode check item 6.4 Default Mode
(standard).
8. OPERATIONS - ADVANCED LEVEL
SET
SET
IN THIS OPERATING MODE THE FLAME SENSOR IS IGNORED AND THE CONTROLLER WILL NOT
DETECT THE PRESENCE/LACK OF FLAME, BEING ESSENTIAL FOR THE OPERATOR TO PAY SPECIAL
ATTENTION TO CONTROL THE OVEN IN ORDER TO PREVENT GAS ACCIDENTS.
7. OPERATIONS - BASIC LEVEL
8.1 Changing the controller parameters
7.4 Enable Default (standard) operating mode
To enable / disable the functions lock, press the
<
and
>
keys and hold for the time configured in
parameter F26 - Time for functions lock.
When this configuration is active, the parameters cannot be changed, but they can be viewed. When the
lock is active, the parameters available for adjustment are defined in parameter F25 - Functions Lock.
Icon
&
indicates the status of the lock. Icon lit indicates the functions lock is active.
SET
SET
Use the
<
or
>
keys to select the desired function. The value can be edited with a quick touch on the key. Use the
<
or
>
keys to change the value and press the key with a quick touch when ready to save the configured value and
return to the functions menu.
To leave the configuration menu and return to the normal operating mode (temperature and time indication), press
(long touch) until
[----]
is displayed.
.
SET
Access the advanced configuration menu by pressing the key for 4 seconds until
[FuNc]
is
displayed. When
[CoD]
is displayed press the key again (quick touch). Use the
<
or
>
keys to
enter the access code 123 and press (quick touch) again when ready.
SET
SET
SET
DESCRIPTION
FUN
MIN
MAX
UNIT
DEF.
FUNCTION
Access code (123)
Required when you want to change the
advanced configuration parameters.
[CoD]
0
9999
-
0
Temperature sensor
indication offset
Allows compensating deviations in the sensor
temperature reading.
[F01]
-20
(-4)
20
(36)
°C
(°F)
0
(0)
8.2 Tabela de parâmetros
SET
