background image

4

11. 

Mount junction box base on expediter. 
Make sure to align slots to properly 
orient junction box base. Tighten nut 
with Terminator-LN-Tool. If mounting 
horizontally, threaded gland holes must 
face downward.

12. 

Install M25 power gland (order 
separately) and M25 blind plug.

13. 

Install power cable.

14. 

Install electronic control module and 
complete system wiring. Terminal set 
screws shall be tightened to a torque 
value of 1,4 Nm (12,4 lb-in). See page 5 
for wiring details. Set modules electronic 
control and/or control limiter at desired 
setpoints.

16. 

Use screwdriver to ratchet on junction 
box lid. Lid will rotate 30 degrees. Install 
junction box lid and twist hand tight. 
Insert screwdriver into ratchet slots 
located on side of junction box base.

17. 

Lid latch mechanism fully engaged. To 
remove lid, repeat step 16 but in the 
opposite direction.

The Heat Tracing Specialists

®

15. 

Use the rotary switches for settling 
Control and Limit Temperature, 
Celsius or Fahrenheit and Auto or 
Manual reset (Control switches on 
Type "C", Limiter switches on Type 
"L" and both on Type "CL").

Terminator

TM

 ECM-P-XP

 

INSTALLATION PROCEDURES

1725        II 2 GD  Ex eb mb [ib]ib IIC T4, Ex tb IIIC T135°C
               SIRA 12ATEX5239X

IP66

-60

°

C  

  Ta 

  + 55

°

C

IECEx SIR 12.0103X Ex eb mb [ib]ib IIC T4, Ex tb IIIC T135°C

PN 27673

D

o n

ot o

pen

 while

 energized. See installa

tion

 in

str

uc

tio

ns

Te

rm

inator EC

M

 

Fo

r u

se

 as

 an

 adj

ustable

 electronic c

ontro

l m

od

ule

10. 

Fix expediter, RTD, and lead wire to 
pipe.

Summary of Contents for Terminator ECM-P-XP









Reviews: