background image

EC300XL        5-1

Thermo Scientific

Section 5

Warranty Information

THERMO FISHER SCIENTIFIC ST

ANDARD PRODUCT W

ARRANTY

The W

arranty Period starts two weeks from the date your equipment is shipped from our facility

. This allows for shipping time s

o the warranty will go

into effect at approximately the same time your equipment is delivered. The warranty protection extends to any subsequent owner

 during the first year

warranty period. 

During the first year

, component parts proven to be non-conforming in materials or workmanship will be repaired or replaced at 

Thermo's expense, labor

included. Installation and calibration are not covered by this warranty agreement. The T

echnical Services Department must be co

ntacted for warranty

determination and direction prior to performance of any repairs. Expendable items, glass, filters and gaskets are excluded from

 this warranty

Replacement or repair of components parts or equipment under this warranty shall not extend the warranty to either the equipmen

t or to the compo-

nent part beyond the original warranty period. The T

echnical Services Department must give prior approval for return of any com

ponents or equipment.

At Thermo's option, all non-conforming parts must be returned to Thermo Fisher Scientific postage paid and replacement parts ar

e shipped FOB desti-

nation.

THIS W

A

RRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER W

A

RRANTIES, WHETHER WRITTEN, ORAL OR IMPLIED. NO W

A

RRANTIES

OF MERCHANT

ABILITY OR FITNESS FOR A P

ARTICULAR PURPOSE SHALL APPL

Y.

Thermo shall not be liable for any indirect or consequential

damages including, without limitation, damages relating to lost profits or loss of products.

Your local Thermo Sales Office is ready to help with comprehensive site preparation information before your equipment arrives. 

Printed instruction man-

uals carefully detail equipment installation, operation and preventive maintenance.

If equipment service  is required, please call your T

echnical Services Department at 1-800-438-4851 (USA and Canada) or 1-740-3

73-4763. W

e're ready

to answer your questions on equipment warranty

, operation, maintenance, service and special application.  Outside the USA, cont

act your local dis-

tributor for warranty information.

Rev

. 4  4/09

ISO 9001

REGISTERED

Summary of Contents for EC300XL





















Reviews: