Thermo Scientific 1300 Series User Manual Download Page 44

Page: 44 / 130

The protective paper catch grids are retained in the airduct wall by their
own tension.

1. To remove a grid section, push the retaining tab down until the

section can be moved out from under the inner back wall.

2. To install the grid section, first place it on the lip of the back wall,

then push the retaining tab down and towards the back until the
locking tabs are secured behind the inner back wall.

Caution

Do not operate the unit without the paper catch grids installed!

1300 Series A2

5-5

Thermo Scientific

Section 5

Cleaning and Decontamination

Clean the Paper

Catch Grid

Retaining
tab

Grid
section

Inner
back wall

Retaining
tab

Grid section

Figure 5-1.

Protective Paper Catch Grid

Summary of Contents for 1300 Series



































































































































Search results

Summary of Contents for 1300 Series

Reviews:

Related manuals for 1300 Series

Brands by name

Popular brands

Thermo Scientific 1300 Series, User Manual

Search results

Summary of Contents for 1300 Series

Reviews:

Related manuals for 1300 Series

Brands by name

Popular brands