background image

 

VOLTMAX ELECTRIC BOILER Installation and Operation Manual 

(

Revised June 2017)

, Page 

9.

 

General Safety Precautions 

 

Be sure to read and understand the entire Installation & operation manual before attempting to install or to operate this water 
heater. Pay attention to the following General Safety Precautions. Failure to follow these warnings could cause property damage, 
bodily injury or death. Should you have any problems understanding the instructions in this manual, 

STOP

, and get help from a 

qualified installer or technician

 

SECTION 2 : INTRODUCTION 

 

 

These important safeguards and instruction appearing in this manual are not meant to cover all 
possible conditions and situations that may occur. Common sense, 
caution and care are factors that cannot be built into every product. These factors must be 
supplied by the person(s) caring for and operating the unit. 

 

2.1  LOCAL INSTALLATION 
REGULATIONS 

This  electric  boiler  must  be  installed  in 
accordance  with  these  instructions  and  in 
conformity with local codes, or in the absence of 
local  codes,  with  the  National  Plumbing  Code 
and  the  National  Electric  Code,  current  edition. 
In  any  case  where  instructions  in  this  manual 
differ  from  local  or  national  codes,  the  local  or 
national codes take precedence. 
 
 

2.2  CORROSIVE ENVIRONMENT  

The electric boiler must not be installed near an 
air  duct  supplying  corrosive  atmosphere  or  with 
high  humidity  content.  When  a  boiler  defect  is 
caused by such conditions, the warranty will not 
apply.

 

 

2.3  INSPECTION UPON RECEPTION  

Inspect  the  electric  boiler  for  possible  shipping 

damage.  The  manufacturer’s  responsibility 

ceases  upon  delivery  of  goods  to  the  carrier  in 
good  condition.  The  Consignee  must  file  any 
claims  for  damage,  shortage  in  shipments,  or 
non-delivery immediately against the carrier. 
 

2.4  TO BE CHECKED 

Please  refer  to  the  rating  plate  on  the  unit  to 
ensure  that  you  have  the  correct  model  and 
voltage in hand. 
 

 

List of components shipped with the unit: 

• Pressure relief valve set at

 30 PSI. 

• Drain valve.

 

• Temperature & pressure indicator

 

• Outdoor temperature sensor

 

• Installation and operating manual

 

 

 
 

 
The electric boiler should not be installed where it may damage the adjacent structures or lower 
floors in the event of leakage of the tank or connections. If this  cannot be avoided, install a non-
flammable tray or bowl under the boiler to collect and drain water from leaks. 
 
NOTE: Any tray or cuvette MUST conform to local codes. 

 

AVERTISSEMENT 

  ! 

WARNING 

  ! 

Summary of Contents for VOLTMAX 108






































































Reviews: