Thermasol SS-140 Installation Instructions Manual Download Page 15 | Manualshive

Page: 15 / 18

background image

DOC NO. 81078

Page 15 of 18

Rev D 3/06 GM

9.

THESE STEPS MUST BE TAKEN OR YOUR WARRANTY WILL BE VOID.

Coat the entire control

back with supplied waterproof silicon. Completely seal the control to the wall so moisture does not get
behind it. Place the control on the wall pressing firmly. You may need to tape the control into place
until the silicone dries. Be careful not to harm the wall/control with the tape.

Let dry for 24 hours

before using steam bath.

10. Refer to operation instructions for control functions.

Note: Failure to follow installation instructions specifically will cause the warranty to be void.

COAT THE BACK COMPETELY

WITH SUPPLIED WATERPROOF

SILICONE TO COMPLETELY

SEAL THE CONTROL TO THE

WALL AND NOT ALLOW

MOISTURE BEHIND IT

1-1/16“ DRILL HOLE IN WALL

FOR CONTROL CABLE

50 FT. CONTROL CABLE

FROM STEAM GENERATOR

COUPLER

2.95

5.00

Figure 8

CAUTION

Do not use harsh or

abrasive cleaning

chemicals when cleaning

your control.

«
...
13
14
15
16
17
...
»

Summary of Contents for SS-140



















Reviews:

No comments

Related manuals for SS-140

Brand: Balboa Pages: 2

ENSEMBLE 76111120

Brand: Sterling Plumbing Pages: 2

HOTSOAK 69 AI16AIR7036HS

Brand: Aquatic Pages: 1

Hotsoak 71 AI9AIR7444HS

Brand: Aquatic Pages: 1

HOTSOAK 66 AI7AIR6042HS

Brand: Aquatic Pages: 1

Brand: Terraillon Pages: 19

Brand: Canadian Spa Pages: 8

Brand: Canadian Spa Pages: 16

Brand: Gulfstream Plastics Pages: 12

Brand: Jacuzzi Pages: 64

Brand: Jacuzzi Pages: 120

Brand: RainDance Pages: 28

Brand: Laurel Mountain Whirlpools Pages: 4

ELLISSE OVAL 2709

Brand: American Standard Pages: 4

Solares Smart Spa

Brand: ab Pages: 42

Brand: Baja Products Pages: 21

Brand: Myspa Pages: 48

Brand: Dundalk LeisureCraft Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands