background image

14

VENTILATION

EXHAUST PLENUM ADAPTER  INSTALLATION

Wall

10-3/4"

Adapter Shown with Offset to Right

Model # RD7

With Offset to Rear

4-5/8"

With Offset to Left

3-3/8"

2-1/8"

12"

9-1/2"

With Offset to Right

With Offset to Front

Figure 23A  Top View of 7" Round  Adapter in 4 Positions

DETERMINING REMOTE BLOWER DUCTS AND FITTINGS

High levels of air flow provide better performance.  For
best results, use larger duct and keep the duct length as
short as possible.

The VTR1000Q remote blower requires a 10" diameter
round duct to match the inlet ring.  You will need to transition
from other duct sizes to achieve the 10" diameter.  Be sure
to use proper transitions from one size duct to another.

NOTE:   You need to calculate the equivalent lengths of
straight duct for each elbow or transition you use. See
Blower Duct Sizing Section, Page 15 to 17.

1.

Select type of adapter (Figure 21) based on ducting
options (Fig 22).

- 3-1/4" x 10" adapter Model  #RD310

      or

- 7" Diameter Adapter Model  #RD7

2.

Apply foam gasket to flange (Figure 24).

3.

Position adapter over exhaust plenum ring.  Note:  The
adapter's opening allows the choice of 4 positions (see
Figure 23A) or 2 positions (see Figure 23B).

4.

Secure adapter in place with the two mounting brackets
shown in Figure 24.  Tighten wing nuts to compress
gasket.

CL

CL

CL

CL

Summary of Contents for RDDS30V





















Reviews: