background image

 

                

www.theatrelight.co.nz 

 

Theatrelight NZ

PO Box 13-159, Onehunga, Auckland, New Zealand

6 Rowe St, Onehunga, Auckland, New Zealand

Tel: 64-9-622 1187, Fax: 64-9-636 5803,

 

 

 

DMX Start Address Thumbwheel 

Valid DMX start address:   12 Chn: 1-501; 6 Chn: 1-507 
Invalid DMX start address: 12 Chn: 0, 502-999; 6 Chn: 0, 508-999 
 
If an invalid address is selected the start address defaults to 1. 
 

DMX Fail behaviour 

Last DMX levels retained until power off 
All DMX levels initialised to zero at power on  
 

Temperature LED behaviour

 with heatsink temperature: 

LED Off: 

 

under 50 degrees C 

LED 2 sec Flash: 

between 50 and 59 degrees C 

LED On 

 

between 60 and 69 degrees C 

LED Rapid Flash 

70 degrees C or over: all Channels are switched Off   

 

Fan behaviour

 with heatsink temperature 

30 degrees C: 

Fan starts at 50% speed 

- then fan speed increases with each degree C to - 
35 degrees C: 

Fan at 100% speed 

 
The fan stays on for 10 minutes after the internal temperature drops below 30 
degrees 

 
SwitchPack behaviour at power on: 

All LEDs set On for 1 second 
Fan set On at 100% for 1 second 
All Channels set Off for 1 second 

 
SwitchPack behaviour 1 second after power on: 

DMX LED shows DMX state 
Phase ABC LEDs show power state 
Temp LED shows temperature state 
On/Off/DMX mode restored to the original settings before power off 
DMX security mode restored to the original settings before power off 
Keyboard enable/disable state restored to the settings before power off 
 
Note: if power goes off before the 5 minutes timeout of Parameter Save above, the 
new settings will be lost. 
 

 

Summary of Contents for SwitchPack 1210 DMX






Reviews: