background image

 

                

www.theatrelight.co.nz 

 

Theatrelight NZ

PO Box 13-159, Onehunga, Auckland, New Zealand

6 Rowe St, Onehunga, Auckland, New Zealand

Tel: 64-9-622 1187, Fax: 64-9-636 5803,

 
 
 
 
The standard 19 inch rackmount case contains either 6 or 12 Solid State Relays for 
remote switching of loads by DMX control. Solid state relays generate very little 
electromagnetic interference compared to hard switched Relay contacts.    
 
Features: 
 

• 

Solid State Relays use dual SCRs (not Triacs) 

• 

SCRs are continuous pulse train driven for no minimum load limitation 
requirement 

• 

SCRs switch On at voltage zero cross to eliminate current surges at turn-on of 
capacitive loads (as caused by mechanical relay contacts) 

• 

SCRs switch Off  at current zero cross to eliminate voltage spikes at turn-off of 
inductive loads (as caused by mechanical relay contacts) 

• 

Firing angle in each half-cycle (and hence energy) always maintained equal, 
and only positive and negative 

pairs

 of half-cycle energy are fed to the load 

This results in a very low DC component to protect magnetic transformers 
from core saturation and consequent fire hazard   

• 

SCRs are voltage surge and spike protected 

• 

Overload limited by thermistor (channels are switched off on long-term over-
current to limit damage due to over-heating) 

• 

Minimum volts loss to load - only 1.5 volts  

 

• 

On or Off states may be controlled by DMX remotely, or locally from the 
internally lit front panel pushbuttons.  

• 

When DMX controlled, channels turn at 60% and turn off at 40%. This 
hysteresis provides flicker-free On/Off switching 

• 

Programmable security delays to prevent switch on off of critical loads 

• 

Manually controlled channels On/Off state always restored on power up 

• 

DMX controlled channels always power up Off  

• 

Keyboard disable feature to prevent unauthorised operation 

• 

Universal power supply:  90-240vac, 50-60 hertz.  

 

Models: 

 
SwitchPack 1210: 12 channels of 13 amp MCBs. Available with Aust/NZ socket back, 
 

Socapex back, terminal back, or to order 

SwitchPack 1220: 12 channels of 20 amp MCBs. Available with Socapex back, 
 

terminal back, or to order 

SwitchPack 630: 6 channels of 32 amp MCBs. Available with terminal back, or to 
 

order 

 

 

Summary of Contents for SwitchPack 1210 DMX






Reviews: