TGW CRUZcontrol Installation, Operation & Maintenance Manual Download Page 42

Page: 42 / 62

IOM CRUZcontrol®

P/N: 90480009

Revision Date: 03/18/2019

Page

Discharge Logic Assembly

A Discharge Logic Assembly is a Basic Logic Assembly without a solenoid valve attached. It can be

used to control the release from the last, discharge zone of a length of CRUZcontrol. Since there is no

solenoid valve, the same Discharge Logic Assembly will work for either NBA™23 or XenoROL

applications.

The Discharge Logic Assembly is mounted on the charge end of the conveyor immediately downstream

of the last (discharge) zone of a length of CRUZcontrol accumulation conveyor. It is connected to the

Logic Assembly of the discharge zone as shown. There is no need for a Function Module to be attached

to it. The DLA does not need to be given a release signal. Product blocking that photoelectric sensor

will stop release from the CRUZcontrol discharge zone, until the photoelectric sensor clears again. This

operation can usually be left enabled and ready to function regardless of whether the receiving conveyor

is running or off. There would be no need to interface the CRUZcontrol operation with the receiving

conveyor operation, since the functioning of it is based solely on product movement.
The following hardware listing is for two Discharge Logic Assembly kits consisting of the Discharge Logic

Assembly, a reflector, and mounting brackets. The mounting brackets provide for the mounting of the

Discharge Logic Assembly and reflector either ½ inch or 3 inches above a standard XenoROL side

channel. Since every application is different, there will usually be a need to drill mounting holes for the

brackets.

TGW Systems Part Number

Description

E0006240

Discharge Logic Assembly Kit, ½ inch above rollers scan

height

E0006236

Discharge Logic Assembly Kit, 3 inch above rollers scan

height

CONVEYOR FLOW

DISCHARGE

LOGIC

ASSEMBLY

LOGIC

ASSEMBLY

Receiving Conveyor

(Without CRUZcontrol)

CRUZcontrol

Discharge Zone

Summary of Contents for CRUZcontrol































































Search results

Summary of Contents for CRUZcontrol

Reviews:

Related manuals for CRUZcontrol

Brands by name

Popular brands

TGW CRUZcontrol, Installation, Operation & Maintenance Manual

Search results

Summary of Contents for CRUZcontrol

Reviews:

Related manuals for CRUZcontrol

Brands by name

Popular brands