TGB EST 1000 Service Manual Download

Page: 237 / 269

7-3. BRAKE SYSTEM AND BODY COVER

7-3-6

MASTER CYLINDER

Master Cylinder Removal (Hand Brake)

1. Drain brake system.

2. Remove master cylinder.

3. Unscrew brake hose from master cylinder.

Master Cylinder Removal (Pedal Brake)

4. Disconnect master cylinder rod from brake

pedal.

5. Remove master cylinder rod from master

cylinder.

6. Remove master cylinder retaining bolts and

nuts.

7. Remove master cylinder from vehicle.

Master Cylinder Inspection

▪

. Check boot for crack.

▪

. Check rod for wear and scratch.

▪

. Check master cylinder housing for leak or

damage.

Master Cylinder Installation

▪

. For installation, reverse the removal

procedure.

▪

. Tighten brake light switch and front brake

hoses to specification.

TORQUE:

Pedal Master Cylinder bolts:208-320kgf-cm.

Break hose = 300-350 kgf-cm.

Brake light switch =

300-350 kgf-cm.

Pedal reservoir bolt: 100-120 kgf-cm.

▪

. Lubricate push rod end and inside master

cylinder boot.

▪

. Install new sealing washers.

▪

. Refill and bleed brake system.

▪

. Adjust master cylinder rod.

Summary of Contents for EST 1000














































































































































































































































































Search results

Summary of Contents for EST 1000

Reviews:

Related manuals for EST 1000

Brands by name

Popular brands

TGB EST 1000, Service Manual

Search results

Summary of Contents for EST 1000

Reviews:

Related manuals for EST 1000

Brands by name

Popular brands