background image

Control Interfaces

www.ti.com

The D-divider value is 14-bits wide and is controlled by 2 registers. For proper update of the D-divider
value, Page 0, Register 7 must be programmed first followed immediately by Page 0, Register 8. Unless
the write to Page 0, Register 8 is completed, the new value of D will not take effect.

The clocks for codec and various signal processing blocks, CODEC_CLKIN can be generated from MCLK
input, BCLK input, GPIO input or PLL_CLK (Page 0/Register 4/D(1:0) ).

If the CODEC_CLKIN is derived from the PLL, then the PLL must be powered up first and powered down
last.

Table 2-23

lists several example cases of typical MCLK rates and how to program the PLL to achieve a

sample rate Fs of either 44.1kHz or 48kHz.

Table 2-23. PLL Example Configurations

Fs = 44.1kHz

MCLK (MHz)

PLLP

PLLR

PLLJ

PLLD

MADC

NADC

AOSR

MDAC

NDAC

DOSR

2.8224

1

3

10

0

3

5

128

3

5

128

5.6448

1

3

5

0

3

5

128

3

5

128

12

1

1

7

560

3

5

128

3

5

128

13

1

2

4

2336

13

3

64

4

6

104

16

1

1

5

2920

3

5

128

3

5

128

19.2

1

1

4

4100

3

5

128

3

5

128

48

4

1

7

560

3

5

128

3

5

128

Fs = 48kHz

2.048

1

3

14

0

2

7

128

7

2

128

3.072

1

4

7

0

2

7

128

7

2

128

4.096

1

3

7

0

2

7

128

7

2

128

6.144

1

2

7

0

2

7

128

7

2

128

8.192

1

4

3

0

2

8

128

4

4

128

12

1

1

7

1680

2

7

128

7

2

128

16

1

1

5

3760

2

7

128

7

2

128

19.2

1

1

4

4800

2

7

128

7

2

128

48

4

1

7

1680

2

7

128

7

2

128

2.8

Control Interfaces

The TLV320DAC3203 control interface supports SPI or I

2

C communication protocols, with the protocol

selectable using the SPI_SELECT pin. For SPI, SPI_SELECT should be tied high; for I

2

C, SPI_SELECT

should be tied low. It is not recommended to change the state of SPI_SELECT during device operation.

2.8.1 I

2

C Control Mode

The TLV320DAC3203 supports the I

2

C control protocol, and will respond to the I

2

C address of 0011000.

I

2

C is a two-wire, open-drain interface supporting multiple devices and masters on a single bus. Devices

on the I

2

C bus only drive the bus lines LOW by connecting them to ground; they never drive the bus lines

HIGH. Instead, the bus wires are pulled HIGH by pullup resistors, so the bus wires are HIGH when no
device is driving them LOW. This way, two devices cannot conflict; if two devices drive the bus
simultaneously, there is no driver contention.

Communication on the I

2

C bus always takes place between two devices, one acting as the master and the

other acting as the slave. Both masters and slaves can read and write, but slaves can only do so under
the direction of the master. Some I

2

C devices can act as masters or slaves, but the TLV320DAC3203 can

only act as a slave device.

An I

2

C bus consists of two lines, SDA and SCL. SDA carries data, and the SCL signal provides the clock.

All data is transmitted across the I

2

C bus in groups of eight bits. To send a bit on the I

2

C bus, the SDA line

is driven to the appropriate level while SCL is LOW (a LOW on SDA indicates the bit is zero, while a HIGH
indicates the bit is one).

66

TLV320DAC3203 Application

SLAU434 – May 2012

Submit Documentation Feedback

Copyright © 2012, Texas Instruments Incorporated

Summary of Contents for TLV320DAC3203
























































































































Reviews: