Texas Instruments ThunderLAN TNETE100A Programmer'S Manual Download Page 65 | Manualshive

Page: 65 / 179

background image

Resetting

3-8

3.2

Resetting

Resetting ThunderLAN is required when conditions such as an incorrect pow-
er-up cause the register value in the device to deviate from that needed for
proper operation. To perform either a software or hardware reset, the program-
mer must complete the steps indicated.

3.2.1

Hardware Reset

The IEEE 802.3 specification defines a power-up routine which must be fol-
lowed to ensure that ThunderLAN’s internal 10Base-T PHY powers up correct-
ly. This routine also allows for the additional delay necessary when a crystal
is used to drive the FXTL1 and FXTL2 lines.

1) Sync all attached PHYs

2) Isolate all attached PHYs by writing the PDOWN, LOOPBK, and ISOLATE

bits into the control register (the GENen_ctl register in ThunderLAN)

3) Enable the internal PHY by writing 0x4000h (LOOPBK) in the GENen_ctl

register

4) Wait 500 ms for the crystal frequency to stabilize

5) Reset the PHY state machine by asserting the LOOPBK and RESET bits

in the GENen_ctl register

6) Resync the internal PHY

7) Read the control register until bit 15 (RESET) = 0 and the PHY comes out

of reset. This is the time needed to read the register.

8) Load the selected PHY options into the GENen_ctl register

9) If using the attachment unit interface (AUI) mode, set the AUI bit in the

TLPHY_ctl register

10) Wait one second for the clocks to start

«
...
63
64
65
66
67
...
»

Summary of Contents for ThunderLAN TNETE100A




















































































































































































Reviews:

No comments

Related manuals for ThunderLAN TNETE100A

Brand: CAME Pages: 4

Brand: IBM Pages: 4

Brand: IEI Technology Pages: 21

Brand: Octavo Pages: 28

Brand: Obihai Pages: 2

S5120V3-EI Series

Brand: H3C Pages: 54

Brand: Ublox Pages: 116

Brand: H3C Pages: 116

TotalStorage SAN16M-R SAN

Brand: IBM Pages: 116

Brand: DAQ system Pages: 41

Brand: DAQ system Pages: 19

Brand: IBM Pages: 32

JetWeb JX2-PR0FI1

Brand: Jetter Pages: 67

Brand: Zoom Pages: 88

Brand: Tripp Lite Pages: 3

Brand: Patton electronics Pages: 12

Brand: XtendLan Pages: 21

Brand: Ariesys Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands