Texas Instruments OMAP36 Series Technical Reference Manual Download

Page: 3012 / 3738

Hard or soft reset

Next command

Main process

Read SPIm.MCSPI_SYSSTATUS

SPIm.MCSPI_SYSSTATUS

[0] = 1?

Yes

Module configuration:

Write SPIm.MCSPI_MODULCTRL

Write SPIm.MCSPI_SYSCONFIG

mcspi-018

Public Version

McSPI Basic Programming Model

www.ti.com

20.6 McSPI Basic Programming Model

20.6.1 Initialization of Modules

Figure 20-26

shows the overview of the module initialization flow process.

Section 20.6.2

and

Section 20.6.3

show the steps required to configure McSPI modes.

Figure 20-26. Module Initialization Flow

NOTE:

Before the SPIm.

MCSPI_SYSSTATUS

[0] RESETDONE bit is set, the CLK and CLKSPIREF

clocks must be provided to the module.

To avoid unpredictable behavior, reset the module before changing from master mode to
slave mode, or vice versa.

20.6.2 Transfer Procedures without FIFO

In the subsections below, the transfer procedures are described without FIFO using
(

MCSPI_CHxCONF

[27:28] FFER and FFEW = 0).

The McSPI allows the transfer of one or more words based on the different modes:
•

Master normal, master turbo, slave

•

Transmit-and-receive, transmit-only, receive-only

•

Write and read requests: Interrupts, DMA

3012

Multichannel SPI

SWPU177N – December 2009 – Revised November 2010

«
...
3010
3011
3012
3013
3014
...
»

Summary of Contents for OMAP36 Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OMAP36 Series

Reviews:

Related manuals for OMAP36 Series

Brands by name

Popular brands

Texas Instruments OMAP36 Series, Technical Reference Manual

Search results

Summary of Contents for OMAP36 Series

Reviews:

Related manuals for OMAP36 Series

Brands by name

Popular brands