manualshive.com logo in svg

Texas Instruments LMK5B33216EVM, User Manual, Page: 6 / 53

Share
Download
Texas Instruments LMK5B33216EVM User Manual Download Page 6

3 EVM Configuration

The LMK5B33216 is a highly-configurable clock chip with multiple power domains, PLL domains, and clock input 
and output domains. To support a wide range of LMK5B33216 use cases, the EVM was designed with more 
flexibility and functionality than needed to implement the chip in a customer system application.

This section describes the power, logic, and clock input and output interfaces on the EVM, as well as how to 
connect, set up, and operate the EVM. Refer to 

Figure 4-1

.

Table 3-1. Key Components Reference Designators and Descriptions

ITEM NO.

REFERENCE
DESIGNATORS

DESCRIPTION

1

U1

LMK5B33216

2

J500 (VIN4 terminal block header)

External Supply, +12-V DC using default 
configuration.

3

A

Y1

Onboard TCXO. Y1 will provide improved 
holdover stability and allow narrower DPLL 
loop bandwidths to be used in comparison to 
the external XO input.

B

J8

SMA connector for external XO. To use the 
external XO, remove the jumper from JP4.

4

J4/5, J6/7

SMA Ports for Clock Inputs (IN0_P/N and 
IN1_P/N).
IN0_N is not populated and IN0_P is 
configured for single ended input. IN1 is 
configured for differential input.

5

J9/11, J10/12, J13/15, J14/16, J17/19, 
J18/20, J21/J23, J22/24, J25/27, J26/28, 
J29/31, J30/32, J33/35, J34/36, J37/39, 
J38/40

SMA Ports for Clock Outputs

6

S5

Normally open. Push button for device power 
down (PDN pin). R76 enables control of the 
PDN pin through the GUI.
R76 is installed by default.

7

JP5

Jumper header for I

2

C/SPI interface (MCU to 

LMK5B33216)

8

D6

SCL or SCK busy indication LED.

9

J41

USB Port for MCU

EVM Configuration

www.ti.com

6

LMK5B33216EVM User's Guide

SNAU263A – FEBRUARY 2022 – REVISED JULY 2022

Submit Document Feedback

Copyright © 2022 Texas Instruments Incorporated

Summary of Contents for LMK5B33216EVM






















































Reviews:

No comments