manualshive.com logo in svg

Texas Instruments LMK5B33216EVM, User Manual, Page: 39 / 53

Share
Download
Texas Instruments LMK5B33216EVM User Manual Download Page 39

When the DPLL is not used, the APLLs support an APLL-only mode with a programmable 24-bit denominator. 
Support for this mode is currently not implemented in the TICS Pro software.

Figure 6-13. APLL1 Page

Figure 6-14

 shows the post divider for PLL2. 

Figure 6-15

 shows the post divider for PLL3. PLL3 supports all 

outputs of the LMK5B33216.

Figure 6-14. PLL2 Post Divider

Figure 6-15. PLL3 Dividers

6.4.1 APLL DCO

To use the DCO shift controls on a given APLL, enter the DCO ppb step value into the 

DCO Step Size (ppb) 

box shown below. The entered step size will be used to calculate a numerator deviation and a 2s complement 
numerator deviation. To perform the shift, the increment or decrement button must be pressed. An increment 
will write the numerator deviation to the DPLLx_FREE_RUN control which will result in a positive frequency shift 
in the amount specified by the 

DCO Step Size (ppb)

. An decrement will write the 2s complement numerator 

deviation to the DPLLx_FREE_RUN control which will result in a negative frequency shift in the amount specified 
by the 

DCO Step Size (ppb)

.

www.ti.com

Appendix A - TICS Pro LMK5B33216 Software

SNAU263A – FEBRUARY 2022 – REVISED JULY 2022

Submit Document Feedback

LMK5B33216EVM User's Guide

39

Copyright © 2022 Texas Instruments Incorporated

Summary of Contents for LMK5B33216EVM






















































Reviews:

No comments