manualshive.com logo in svg

Texas Instruments LMK04826, Manual, Page: 92 / 113

Share
Download
Texas Instruments LMK04826 Manual Download Page 92

LMK04821, LMK04826, LMK04828

SNAS605AR – MARCH 2013 – REVISED DECEMBER 2015

www.ti.com

9.7.9.4 OPT_REG_2

This register must be written with the following value depending on which LMK0482x family part is used to
optimize VCO1 phase noise performance over temperature. This register must be written before writing register
0x168 when using VCO1.

Table 77. Register 0x17D

BIT

NAME

DESCRIPTION

51: LMK04821

7:0

OPT_REG_2

119: LMK04826
51: LMK04828

9.7.9.5 RB_PLL1_LD_LOST, RB_PLL1_LD, CLR_PLL1_LD_LOST

Table 78. Register 0x182

BIT

NAME

DESCRIPTION

7:3

N/A

Reserved

2

RB_PLL1_LD_LOST

This is set when PLL1 DLD edge falls. Does not set if cleared while PLL1 DLD is low.

Read back 0: PLL1 DLD is low.

1

RB_PLL1_LD

Read back 1: PLL1 DLD is high.

To reset RB_PLL1_LD_LOST, write CLR_PLL1_LD_LOST with 1 and then 0.
0: RB_PLL1_LD_LOST will be set on next falling PLL1 DLD edge.

0

CLR_PLL1_LD_LOST

1: RB_PLL1_LD_LOST is held clear (0). User must clear this bit to allow RB_PLL1_LD_LOST to
become set again.

9.7.9.6 RB_PLL2_LD_LOST, RB_PLL2_LD, CLR_PLL2_LD_LOST

Table 79. Register 0x0x183

BIT

NAME

DESCRIPTION

7:3

N/A

Reserved

2

RB_PLL2_LD_LOST

This is set when PLL2 DLD edge falls. Does not set if cleared while PLL2 DLD is low.

PLL1_LD_MUX or PLL2_LD_MUX must select setting 2 (PLL2 DLD) for valid reading of this bit.

1

RB_PLL2_LD

Read back 0: PLL2 DLD is low.
Read back 1: PLL2 DLD is high.

To reset RB_PLL2_LD_LOST, write CLR_PLL2_LD_LOST with 1 and then 0.
0: RB_PLL2_LD_LOST will be set on next falling PLL2 DLD edge.

0

CLR_PLL2_LD_LOST

1: RB_PLL2_LD_LOST is held clear (0). User must clear this bit to allow RB_PLL2_LD_LOST to
become set again.

92

Submit Documentation Feedback

Copyright © 2013–2015, Texas Instruments Incorporated

Product Folder Links:

LMK04821 LMK04826 LMK04828

Summary of Contents for LMK04826


















































































































Reviews:

No comments