background image

User's Guide

SLAU250 – May 2008

1.5-GHz Low-Phase Noise Clock Evaluation Board

This user's guide discusses the general operation and configuration of the Texas Instruments CDCE72010
evaluation board.

Contents

1

Features

.......................................................................................................................

2

2

General Description

.........................................................................................................

2

3

Signal Path and Control Circuitry

.........................................................................................

3

4

Software Selectable Options

..............................................................................................

3

5

Installing the GUI Interface and USB Driver

.............................................................................

3

6

CDCE72010 Control GUI Interface

.......................................................................................

5

7

TI CDCE72010 Control GUI Interface

....................................................................................

5

7.1

Using Software-Enabled PLL Selection

..........................................................................

5

8

Configuring the Board

.....................................................................................................

10

8.1

Default Configuration for Programming and Testing With USB Cable Attached

..........................

10

8.2

Configuration for Programming With USB Cable Attached

..................................................

10

8.3

Configuration for Testing From a Saved Configuration With USB Cable Removed After
Programming

.......................................................................................................

10

8.4

Configuration for Onboard External Loop Filter

...............................................................

11

8.5

Configuration for PLL Lock Detect

..............................................................................

12

9

CDCE72010EVM Board Schematic Diagram

..........................................................................

13

List of Figures

1

CDCE72010EVM Board

....................................................................................................

2

2

CDCE72010EVM External Loop Filter Topology

.......................................................................

12

Windows is a trademark of Microsoft Corporartion.

SLAU250 – May 2008

1.5-GHz Low-Phase Noise Clock Evaluation Board

1

Submit Documentation Feedback

Summary of Contents for CDCE72010





















Reviews: