Gigabyte MW31-SP0, Quick Reference Manual

Page: 1 / 2

1 2 3 4 5 6
7
8
9
11
10
12
13
14
15
16 17 18 19 20 21 22 23 24
31
32
33
34
36
37
38
39
40 41
42
43
46
47
48
49 50
51
52
45
44
25
26
27
28
29
30
35
Front Panel Header/
前面板 HDD Back Plane Board Header/
硬盤背板排針
ATX Power/
电源
PMBUS
Installing CPU/
安装
CPU Memory Population Configuration/
安装内存
Type
Ranks Per
DIMM and
Data Width
Speed (MT/s);
Slot Per Channel (SPC) and
DIMM Per Channel (DPC)
UDIMM
Unbuffered
DDR4 ECC
UDIMM
Unbuffered
DDR4 non-ECC
SR 1.2V
1.2V
2133 2133
Supported
Voltage
DR 2133 2133
2 Slot Per Channel
1DPC 2DPC
Rear I/O Connector/
后面板接口
Off
State Description
Yellow On 1Gbps data rate
Green On 100Mbps data rate
10Mbps data rate
SATA Connector/SATA
接口
SATA SGPIO Header/
串行
GPIO
SATA DOM Power Connector
TPM Connector/
可信平台模块
COM2 Connector
CPU/System FAN/
风扇
USB 3.0 Header
USB 2.0 Header
Front Audio Connector/
前置音频
S/PDIF In/Out Header
Thunderbolt Add-On
Card Header
1 5
No. Pin Define
1 GPIOA
2 GPIOB
3 SLP_S3
4 SLP_S5
5 GND
Case Open Intrusion Header NVidia SLI – System BIOS setting
Open: Normal operation.
To get best SLI performance, it is recommended
by NVidia to disable VT-d
Please follow below instructions to disable VT-d
function.
1. Press “DEL” to enter BIOS setup menu
2. Select Chipset > VT-d [Enabled] > VT-d
[Disabled]
Closed: Active chassis intrustion alert.
Jumper Settings/
跳线设置
1
2
3
4
5
1
4
2 3 3
4 4
6
7
8
9 12
13
11
10
5
MW31-SP0 Quick Reference Guide/
快速测试参考指南
1
1
1
1
4
4
5
1 5
4 8
1
1
8 2
7 1
7
24 23
2
1 2
13 14
1 2
2 1
10 9
2 1
1
1
1
S/PDIF In
S/PDIF Out
1
10 9
25 26
No. Pin Define
1 3.3V
2 3.3V
3 GND
4 +5V
5 GND
6 +5V
7 GND
8 Power Good
9 5VSB
10 +12V
11 +12V
12 3.3V
No. Pin Define
1 GND
2 GND
3 GND
4 GND
5 +12V
6 +12V
7 +12V
8 +12V
No. Pin Define
1 PMBus Clock
2 PMBus Data
3 PMBus Alert
4 GND
5 3.3V Sense
No. Pin Define
1 GND
2 +12V
3 Sense
4 Speed Control
No. Pin Define
1 GND
2 TXP
3 TXN
4 GND
No. Pin Define
1 Clock
2 P_3V3_AUX
3 LPC_RST
4 P3V3
5 LPC_LAD0
6 IRQ_SERIAL
7 LPC_LAD1
8 No Connect
9 LPC_LAD2
10 No Pin
11 LPC_LAD3
12 GND
13 LPC_FRAME_N
14 GND
No. Pin Define
1 MIC2_L
2 GND
3 MC2_R
4 P3V3
5 LINE2_R
6 MIC2_JD
7 F_Audio_Sense
8 No Pin
9 LINE2_L
10 LINE2_JD
No. Pin Define
1 P_5V_AUX
2 SPDIF-IN
3 GND
No. Pin Define
1 SPDIF-OUT
2 GND
No. Pin Define
1 NDCD-
2 NSIN
3 NSOUT
4 NDTR-
5 GND
No. Pin Define
1 5V for SATA DOM
2 GND
3 No Connect
No. Pin Define
1 5V for SATA DOM
2 GND
3 No Connect
No. Pin Define
1 Power (5V)
2 Power (5V)
3 USB DX-
4 USB DY-
5 USB DX+
No. Code Description
1 COM1 Serial port
2 HD_AUDIO Audio connectors
3 DP_HDMI Display port port (top) / HDMI port (bottom)
4 USB_LAN1 LAN port #1 (top) / USB 3.0 ports (bottom)
5 USB_LAN2 LAN port #2 (top) / USB 3.0 ports (bottom)
6 PS2_USB2 PS/2 connector (top)/USB 2.0 ports (buttom)
7 SYS_FAN0 System fan connector#0
8 P2 8 pin power connector (for CPU)
9 PMBUS PMBus connector
10 CPU0 Intel LGA1151 Socket H4
11 CPU0_FAN CPU fan connector
12 DIMM_P0_A0 Channel 1 slot 0
13 DIMM_P0_A1 Channel 1 slot 1
14 DIMM_P0_B0 Channel 2 slot 0
15 DIMM_P0_B1 Channel 2 slot 1
16 SYS_FAN1 System fan connector#1
17 P1 24 pin main power connector
18 SYS_FAN2 System fan connector#2
19 SYS_FAN3 System fan connector#3
20 SATA_SGP1 SATA SGPIO header
21 SATA4_5 SATA 3 6Gb/s connectors
22 SATA6_7 SATA 3 6Gb/s connectors
23 SATA0/SATA1 SATA 3 6Gb/s connectors (Supports SATA DOM)
24 SATA2/SATA3 SATA 3 6Gb/s connectors
25 SATA_DOM1 SATA port 1 DOM power connector
26 SATA_DOM0 SATA port 0 DOM power connector
No. Pin Define
1 Power LED+
3 No Pin
5 Power LED-
7 HDD LED+
9 HDD LED-
11 Power Button
13 GND
15 Reset
17 GND
19 No Connect
21 No Connect
23 NMI Switch-
No. Desription
1 PS/2 Keyboard/Mouse Port
2 USB 2.0 port
3 USB 3.0 port
4 GbE Eternet LAN port
5 Display port
6 HDMI port
7 Center/Subwoofer Speaker Out Jack (Orange)
No. Desription
1 Clear CMOS Jumper
1-2 Close: Normal operation (Default setting)
2-3 Close: Clear CMOS data.
2 ME Update Jumper
1-2 Close: Normal operation (Default setting)
2-3 Close: ME update mode.
3 BIOS Recovery Jumper
1-2 Close: Normal operation. (Default setting)
2-3 Close: BIOS recovery mode.
4 ME Recovery Jumper
1-2 Close: Normal operation. (Default setting)
2-3 Close: ME recovery mode.
5 Clearing Supervisor Password Jumper
1-2 Close: Normal operation. (Default setting)
2-3 Close: Skip supervisor password.

All channels in system run at the fastest common frequency.

Mixing ECC and non-ECC UDIMMs anywhere on the platform is not supported.

1 and 2 DPC is supported at 2133MHz.

所有通道模式以最快的频率速度运行。

此主板不支持ECC与非ECC内存模组混合使用。

1
与
2 DPC
均支持
2133MHz
速度
。
The HDMI connector is HDCP compliant and supports Dolby True HD and DTS HD
Master Audio formats. It also supports up to 192KHz/24bit 8-channel LPCM audio
output. You can use this port to connect your HDMI-supported monitor. The
maximum supported resolution is 4096x2160@24Hz or 2560x1600@60Hz, but the
actual resolutions supported are dependent on the monitor being used.
Speed LED
10/100/1000 LAN LED:
Link/Activity
LED
13
12
24
No. Code Description
27 BIOS_RCVR BIOS recovery jumper
28 CASE_OPEN Case open intrusion alert header
29 ME_RCVR ME recovry jumper
30 USB_A1 Type A USB 2.0 connector
31 BP_1 HDD back plane board header
32 FP_1 Front panel header
33 F_USB3 USB 3.0 header
34 F_USB2 USB 2.0 header
35 BIOS_PWD Clearing Supervisor Password jumper
36 F_USB1 USB 2.0 header
37 TPM TPM module connector
38 COM2 Serial port cable connector
39 F_AUDIO Front audio connector
40 PCI_1 PCI 32/33MHz slot
41 PCI_2 PCI 32/33MHz slot
42 PCIE_1 PCI Express x4 slot
43 BAT Battery socket
44 CLR_CMOS Clear CMOS jumper
45 ME_UPDATE ME update jumper
46 PCIE_2 PCI Express x16 slot
47 M2_MKEY M.2 slot (Dimension: 2280)
48 PCIE_3 PCI Express x16 slot
49 MEZZ_1 Proprietary PCI Express x4 slot for Mezzanine Card
50 SPDIF_IN S/PDIF in header
51 TBT Thunderbolt add-on card connector
52 SPDIF_OUT S/PDIF out header
No. Pin Define
13 3.3V
14 -12V
15 GND
16 PS_ON
17 GND
18 GND
19 GND
20 -5V
21 +5V
22 +5V
23 +5V
24 GND
No. Pin Define
2 5V Standby
4 No Connect
6 No Connect
8 No Connect
10 No Connect
12 LAN1 Active LED+
14 LAN1 Link LED-
16 SMBus Data
18 SMBus Clock
20 Case Open
22 LAN2 Active LED
24 LAN2 Link LED-
No. Pin Define
1 No Connect
3 No Connect
5 No Connect
7 Key Pin
9 GND
11 BP_LED_G_N
13 NC
15 GND
17 GND
19 P_3V3_AUX
21 P_3V3_AUX
23 GND
25 BP_PRESENSE
No. Pin Define
2 No Connect
4 FAN_SGP_GLD
6 GND
8 Reset
10 BP_LED_A_N
12 GND
14 NC
16 SMB_BP_DATA
18 SMB_BP_CLK
20 No Connect
22 No Connect
24 Key Pin
26 GND
No. Pin Define
1 No Connect
2 No Pin
3 Data Out
4 GND
No. Pin Define
5 GND
6 Load
7 No Connect
8 Clock
1 20
10 9
2 1
10 11
No. Pin Define
1 Power
2 IntA_P1_SSRX-
3 IntA_
4 GND
5 IntA_P1_SSTX-
6 IntA_
7 GND
8 IntA_P1_D-
9 In
10 NC
11 In
12 IntA_P2_D-
13 GND
14 IntA_
15 IntA_P2_SSTX-
16 GND
17 IntA_
18 IntA_P2_SSRX-
19 Power
20 No Pin
No. Desription
8 Rear Speaker Out Jack (Black)
9 Optical S/PDIF Out Connector
10 Line In Jack (Blue)
11 Line Out Jack (Green)
12 Mic In Jack (Pink)
13 Serial port
No. Pin Define
5 RXN
6 RXP
7 GND
No. Pin Define
6 USB DY+
7 GND
8 GND
9 No Pin
10 No Connect
No. Pin Define
6 NDSR-
7 NRTS-
8 NCTS-
9 NRI-
10 No Pin
P/N:12QM1-MW31S0-00R