manualshive.com logo in svg

TETRALEC DN-107NE, Operation Manual

Share
Download
TETRALEC DN-107NE Operation Manual Download Page 4

CHAPTER 2 

GENERAL CHARACTERISTICS 

2-1 

DN-107NE display series 

 

 

 

 

 

 

 

 

Supply Voltage...........................................88 to 264 VAC 47 to 63Hz or 19 to 36VDC. 
Consumption ............................................. 36Va. 
Display ........................................................ 7 segments, 57mm high + decimal point. 

.....................................................................Red LED colour. Viewing distance: 30 meters. 

Parameter memory .................................... Eeprom. 
Communication ......................................... Ethernet 10/100. RJ-45 connector. 
Communication Protocols ........................ TCP/IP, UDP/IP and Modbus/TCP. 
Environmental Conditions ........................ Operation Temperature: -20 to 60ºC. 

.....................................................................Storage temperature: -30ºC to 70ºC. 
.....................................................................Humidity: 5-95% RH non condensing. 
.....................................................................Maximum environmental illumination: 1000 lux. 
.....................................................................Sealing: IP41. 

2. GENERAL CHARACTERISTICS

 

2.1. Electrical characteristics of the displays

 

2.1.1. Electrical characteristics of the DN-107/NE displays.

 

Summary of Contents for DN-107NE
























Reviews:

No comments

Brands by name

Popular brands

Load more brands