background image

 

                  10521 Gulfdale, San Antonio, TX 78216  I   

www.terrawave.com

  I  Email: 

[email protected]

  I  Phone:  210-375-8482

 

 

Version 1.1 - Page 2 

Introduction 
 

The TWSD16128PHC is intended to be used with WLAN / Networking devices.  The 
TWSD16128PHC is intended to be used both indoors and outdoors and to provide NEMA 3R 
protection with cooling and heating. 
 
Maximum internal ambient is 45 Degrees Celsius. 

 

Before installing this product, read these instructions carefully.  Failure to follow these 
instructions could lead to damaging the product or cause a hazardous condition. 
 
Check the ratings on the products you intend to place inside the enclosure solution to ensure 
that this is suitable for your application. 
 
 

Precautions 
 

Read and understand all instructions before you begin installing the unit 

 

When installing and using this product, basic safety precautions should always be followed to 
reduce the risk of electric shock, fire and injury to persons including the following: 
 
All wiring that connects to this equipment must meet applicable local and national building 
codes and network wiring standards for communications cable. 
 

WARNING

:  To prevent the risk of electric shock and equipment damage, disconnect any 

and all supply mains connection to the enclosure before installing, maintaining or trouble 
shooting this product or any products inside the enclosure.   
 
Retain the instructions for future reference. 
 
Follow all warnings and instructions marked on the product. 
 
Insulation on all cables and wires installed the service center must either be PVC, TFE, 
PTFE, FEP, Neoprene, or Polymide. 
 
Never install cable, connectors or jacks in a wet location unless they are specifically designed 
for wet locations. 
 
Never install this product during a lightning storm.  There is a risk of electric shock from 
lightning. 
 
Never touch uninsulated communication wires or terminals. 
 
Disconnect power before cleaning or servicing the unit. 

Summary of Contents for TWSD16128PHC













Reviews: