Terex Genie GS-2669 BE Service Manual Download

Page: 109 / 205

May 2015

Service Manual

Manifolds

Part No. 1257106

GS-2669 BE • GS-3369 BE • GS-4069 BE

50 Press the Enter button.

Result: The ground controls LCD display will

show the following:

Note: After 1 second the display will return to

SELECT OPTION, DOWN DELAY.

51 Push in the red Emergency Stop button to the

off position.

52 Perform Maintenance Procedures,

Test the

Platform overload System

and

Down Limit

Switch Decent delay

How to Adj ust the Pl atform U p R elief Valve - Models without Pl atform Overl oad

How to Adjust the Platform Up

Relief Valve - Models without

Platform Overload

Note: Verify the hydraulic oil level is within the top

2 inches / 5 cm of the sight gauge.

1 Connect a 0 to 5000 psi / 0 to 350 bar

pressure gauge to test port #1 (TP1) on the

function manifold.

1 platform up relief valve
2 test port #1

Summary of Contents for Genie GS-2669 BE














































































































































































































Search results

Summary of Contents for Genie GS-2669 BE

Reviews:

Related manuals for Genie GS-2669 BE

Brands by name

Popular brands

Terex Genie GS-2669 BE, Service Manual

Search results

Summary of Contents for Genie GS-2669 BE

Reviews:

Related manuals for Genie GS-2669 BE

Brands by name

Popular brands