EN
TRANSLATION OF ORIGINAL INSTRUCTIONS
Adjusting the centre brush.
7KHFHQWHUEUXVKKHLJKWLVIDFWRU\DGMXVWHGIRUKDUGÀRRUVHWWLQJ
)LJ',IXVLQJWKHPDFKLQHRQVRIWÀRRU&DUSHWORRVHQWKH
locking nut pos. 1 Fig. 6/D and turn the adjustment knob pos.
2 Fig. 6/D two full turns clockwise to decrease brush pressure.
Retighten locking nut.
For proper brush adjustment, the bristles should slightly bend
DJDLQVW WKH ÀRRU VXUIDFH $V WKH EUXVK ZHDUV LW¶V LPSRUWDQW WR
increase the brush pressure to maintain optimum sweeping
performance.
Too much brush pressure may prematurely wear
brush and decrease battery run time. When replac-
ing a worn brush, it’s important to readjust the set-
ting back to “0”.
REPLACING AND ADJUSTING THE BELT
To prepare the machine for replacement of one or more belts,
proceed as follows:
•
turn the front cowling, remove the top cowling and the front
bin.
•
DIWHUKDYLQJWDNHQRႇWKHOHIWZKHHOXQVFUHZWKHVFUHZVWKDW
¿[WKHEXPSHUDQGWKHULJKWVLGHFRYHUDQGUHPRYHWKHP
Replacing the side brush belt
•
Remove the belt pos. 7 Fig. 7 from the pulley pos. 6 Fig. 7.
•
8QVFUHZWKH¿[LQJSLQSRV)LJDQGUHOHDVHWKHKRRNVRQ
the side arm pos. 9 Fig. 7 from the idle toothed ring.
•
Remove the belt pos. 7 from the side arm pos. 9 Fig. 7.
•
Replace the belt.
•
Reattach the side arm pos. 9 Fig. 7 to the idle toothed ring.
•
Retighten the pin pos. 8 Fig. 7.
•
Reposition the belt pos. 7 Fig. 7 on the pulley pos. 6 Fig. 7.
Replacing the drive belt
•
Remove the belt pos. 1 Fig. 7.
REPLACING THE FLAPS
2XWHUVLGHÀDSV
7RUHSODFHWKHVLGHÀDSVSRV)LJWDNHRႇWKHEDFNZKHHOV
8QVFUHZWKHVFUHZV¿[LQJWKHÀDSVWRWKHFKDVVLVSRV)LJ
DQGUHSODFHZLWKQHZÀDSV
,QQHUVLGHÀDSV
7RUHSODFHWKHLQQHUVLGHÀDSVSRV)LJOLIWWKHIURQWRIWKH
PDFKLQHDQGXQVFUHZWKHVFUHZVSRV)LJWKDW¿[WKHÀDSV
WRWKHFKDVVLV5HSODFHZLWKQHZÀDSV
&HQWUHÀDS
•
7DNHRႇWKHEDFNZKHHOVDQGWKHFRUUHVSRQGLQJVLGHFRYHUV
•
Remove the drive pulley.
•
Remove the rear bin.
•
8QVFUHZWKHWZRÀDS¿[LQJSLQVSRV)LJRQWKHVLGHV
of the chassis.
•
+ROGWKHÀDSSRV)LJDQGSXOOLWWRZDUGVWKHRXWVLGHRI
the machine.
Reassembly:
•
,QVHUWWKHÀDSLQWKHVDPHGLUHFWLRQDVLWZDVUHPRYHG
•
Insert the two references in the corresponding holes.
•
7LJKWHQWKH¿[LQJSLQVDQGUHDVVHPEOHWKHPDFKLQH
NOTE
2
1
Fig. 6/D
Fig. 7
Fig. 8
- 10 -
