Tenma 72-1016 Operating Manual Download

Page: 8 / 59

Safety Information

This Meter complies with the standards IEC61010: in
pollution degree 2, overvoltage category (CAT. I 1000V,
CAT.II 600V) and double insulation.

CAT III: Distribution level, fixed installation, with smaller
transient overvoltages than CAT. IV
CAT IV: Primary supply level, overhead lines, cable
systems etc.

Use the Meter only as specified in this operating manual,
otherwise the protection provided by the Meter may be
impaired.
In this manual, a

Warning

identifies conditions and

actions that pose hazards to the user, or may damage
the Meter or the equipment under test.

Note

identifies the information that user should pay

special attention to.

International electrical symbols used on the Meter and
in this Operating Manual are explained on

page 8.

Model 72-1016: OPERATING MANUAL

This Manual: http://www.manuallib.com/file/2587080

Summary of Contents for 72-1016




























































Search results

Summary of Contents for 72-1016

Reviews:

Related manuals for 72-1016

Brands by name

Popular brands

Tenma 72-1016, Operating Manual

Search results

Summary of Contents for 72-1016

Reviews:

Related manuals for 72-1016

Brands by name

Popular brands