Temsa TS 35, Electronics And Wiring Manual

Page: 244 / 257

Note:
TEMSA
TS35 09.04.A.fc-5
WABCO – ABS / ASR Fault Codes
SIDFMI ABS-E all
VDC-PD-D T.Munko/G.Ruhnau
SID,
SPN FMI
Blink
Code
FAULT
Basic,
Universal
pin/plug
Fault-
indication
ABS-E with ESC/RSC/A (Universal)
COMMENT (REACTION)
Cause Action
4 1 3 + 3 air gap 17;18/18 WL
ABS: wheel disabled
ASR, RSC/A: disabled
SMR: disabled
air gap too large, sensor output voltage too low
but just exceeds trigger level
Check bearing play, polewheel run out, push sensor to polewheel.
4 2 5 + 3 incorrect tyre 17;18/18 WL
ABS: wheel disabled
ASR, RSC/A: disabled
SMR: disabled
such proportion of tyre diameter/ pole wheel teeth
number that wheel speed difference within front
axle > 10 % or difference within wheels of different
axles > 19 % . Pneus or number of polewheel
teeth are different.
Check wheel circumference and number of polewheel teeth
4 3 4 + 3 shorted to UBATT 17;18/18 WL
ABS: wheel disabled
ASR, RSC/A: disabled
SMR: disabled
DC voltage detected. Short circuit or impedance to
battery voltage.
Check sensor wiring..
4 4 4 + 3 shorted to ground 17;18/18 WL
ABS: wheel disabled
ASR, RSC/A: disabled
SMR: disabled
Short circuit to ground is detected. Check Sensor wiring, replace Sensor if necessary.
4 5 4 + 3 open circuit 17;18/18 WL
ABS: wheel disabled
ASR, RSC/A: disabled
SMR: disabled
Open circuit is detected Check Sensor wiring, replace Sensor if necessary.
4 6 4 + 3 short circuit 17;18/18 WL
ABS: wheel disabled
ASR, RSC/A: disabled
SMR: disabled
Short circuit between sensorwires IG/IGM is
detected
Check Sensor wiring, replace Sensor if necessary.
4 7 6 + 3 incorrect pole wheel 17;18/18 WL
ABS: wheel disabled
ASR, RSC/A: disabled
SMR: disabled
Cyclic drop out detected at speed higher than 10
km/h. Several wheel revolution necessary.
Check polewheel for damages / missing teeth. Use WABCO sensor
probe. Replace polewheel if not checked o.k. If additional airgap
faults are stored, adjust airgap.
4 8 3 + 3 slip 17;18/18 WL
ABS: wheel disabled
ASR, RSC/A: disabled
SMR: disabled
16 sec. slip duration detected.
Adjust airgap. Other possible reasons: gear engaged at slippery
conditions or modulator valve does not work correctly.
4 9 5 + 3 wires mismatched 17;18/18 WL
ABS: wheel disabled
ASR, RSC/A: disabled
SMR: disabled
Wire IG or IGM of another sensor is detected. Check for mismatch-fault of another sensor. Correct harness.
4 10 3 + 3 speed drop-out 17;18/18 WL
ABS: wheel disabled
ASR, RSC/A: disabled
SMR: disabled
Temporarily loss of wheel speed signal. Air gap
too large, sensor voltage exceeds trigger level at
too late.
Adjust airgap. Check sensor wiring and connectors for intermittent
contact. Turn the wheel and read out amplitudes of sensor signals
and compare with required values.
4 11 5 + 3 abnormal speed 17;18/18 WL
ABS: partial disabled
ASR, RSC/A: disabled
SMR: disabled
with standard parameterset not as fault
interpreted. FMI 11 not stored.
Brake squeezes or chatters.
NO repair instruction. Check sensor wiring and connectors for
intermittent contact. Check toothed wheel for damages. Read out
amplitudes of sensor signals and compare with required values.
4 12 5 + 3 frequency too high 17;18/18 WL
ABS: wheel disabled
ASR, RSC/A: disabled
SMR: disabled
non plausible sensor frequency measured.
Check sensor wiring and connectors for intermittent contact. Change
ELECTRONIC if fault occurence repeats.
Wheel Sensor right rear