background image

- 4 -

•  Use of any fluid other than Rosco Smoke Simulation fluid or modification or attempted 
  unauthorized repair of the machine will immediately invalidate the warranty.

•  Machines are designed for continuous use over an 8-hour day, but to protect components, it is wise  
  to turn off the machine when it is not in use.   In permanent installations,  it is advisable to equip  
  the circuit with a night cut-off device.

Additional Precautions: Do’s & Don’ts

•  Do Read the entire manual before operating the machine and pay particular attention to all 
 

CAUTIONS AND WARNINGS.

•  Do Use an extension cord that is properly rated for voltage, current and length, and  is free from  
 

nicks, cuts or other signs of wear.

•  Do Check to see that the machine is clean and free of foreign objects before each  
 

operating period.

•  Do Ensure that the machine is adequately ventilated.
•  Do Use proper caution when handling hot surfaces.
•  Do Use the minimum amount of fog required to achieve the desired effect.
•  Do Not Use the machine near a person who has asthma or similar inhalation disorder.
•  Do Not Use any foreign substances in the machine.
•  Do Not Use a machine that is damaged or operating improperly in any way.
•  Do Not Use a machine that leaks fluid from the housing.
•  Do Not Leave the machine switched on for prolonged periods of time without producing fog.
•  Do Not Enclose the machine.
•  Do Not Install the machine in such a fashion that the operator cannot see the whole machine,  
 

including the indicator lights.

•  Do Not Touch the shielded nozzle of the machine. Allow sufficient cooling time after operation  
 

before attempting to perform maintenance or storage. 

•  Do Not Direct the fog output continuously against nearby surfaces.  This may eventually 
 

cause fluid to re-condense.

Danger! Hazardous 

voltage. Contact will 

cause electric shock.   

Caution! Safety 

hazard. Risk of 

personal injury.   

Caution! Burn 

hazard. Hot surface.

Do not touch   

Caution! Fire hazard. 

Danger! Hazardous 

voltage. Contact will 

cause electric shock.   

Caution! Safety 

hazard. Risk of 

personal injury.   

Caution! Burn 

hazard. Hot surface.

Do not touch   

Caution! Fire hazard. 

Safety Precautions

•  In any facility, the fog concentration should be controlled.  The fog should never mask  
  emergency exits, safety signs, staircases or other safety constructions.

•  After long use, or if the machine is not properly set, some liquid droplets or wet area  
  may appear in front of the machine’s outlet.  This liquid should be wiped up to prevent 
  a condition where someone might slip and fall.

Preventing Improper Operation

•  Unauthorized repair or alteration of any safety devices can lead to improper operation
  and accidents. Repairs should be performed only by an authorized Service Center. 

Summary of Contents for Shadow Nightfall





















Reviews: