background image

TEMA TELECOMUNICAZIONI    

                                                                

AD639R VoIP SIP PoE Repeater 

MAS-AD639R-REV00EN 

 

 

 

 

             

       

               Page 18 of 30 

 

9.5.  Alarm input settings 

 

In this page it is possible to program the behavior of the acquisition input of the external contact: 

 

 

 

 

Call addr.

: IP address of the phone to contact when the alarm condition occurs. 

 

 

Retry:

 number of call attempts (max 999). 

 

 

Separation:

 separation, in seconds, between one call attempt and another (max 999). 

 

 

Delay:

  is  the  minimum  time,  in  seconds,  before  the  input  status  change  is evaluated.  It  can  be  used,  for 

example, to mask a door indicator left open after the visitor has entered. Assuming that the maximum time 
that  the  pedestrian  entrance  must  remain  open  is  30  seconds,  only  at  the  end  of  this  time  a  warning 
telephone call would be sent to the staff in charge. 

 

 

Inversion:

 normally the contact is open and the alarm occurs when the contact is closed. Activating this flag 

it  is  possible  to instruct the  device  to  behave  in  the opposite  way  (the  contact  is  normally  closed  and  the 
alarm occurs at opening). 

 

 

Stop code:

 code to dial on the called telephone to accept and silence the alarm (max 3 digits). 

 

 

Announce:

  the  activation  of  the  input  (of  the  contact  connected  to  him)  causes  the  broadcast  of  a  pre-

recorded message on the local speaker. See message mask for programming voice messages. 

 
 
The system can generate a VoIP call to alert, after triggering the alarm input contact (from auxiliary devices or from 
a button made available in the vicinity) an appointed operator. 
A prerecorded message is played back to the called party. It is possible to invert this logic, so the triggering of the 
signaling can occur following the opening of the contact connected to the input. 
 
AD639R continuously monitors the status of the contact and in the event of activation it will begin to call the person 
who  will  manage  the  situation  detected  on  the  programmed  telephone  number  and  reproduce  the  message 
associated with the event. It is possible to define an acquisition / acknowledgment code for the alarm signal that the 
person  called  must  enter  to  inform  the  device  of  the  taking  of  the  alarm  signal  as  notified.  If  the  called  number 
proves  to  be  busy  or  does  not  answer  or  in  any  other  case  where  AD639R  does  not  receive  the  acquisition  / 
acknowledgment code anyway, at the end of each single call attempt it returns in stand-by and it is ready for a new 
alarm notification. 
 
When  the  AD639R  receives  the  acknowledgment  code,  the  alarm  condition  signaling  stops  and  no  further 
notification calls will be made. To be able to be triggered again the notification phase of an activation, the condition 
that  had  triggered  the  previous  notification  must  return  to  stand-by.  To  Only  following  the  occurrence  of  a  new 
contact activation condition, the notification cycle with notification calls restarts. In practice: if a connected contact 
closes and its activation is detected, AD639R starts making alert calls. 
 
In  the  event  that  the  person  called  by  the  system  reply  and  correctly  enters  the  acknowledgment  code,  the  alert 
calls  will  be  terminated.  To  trigger  a  new  cycle,  the  contact  must  reopen  and  close  again.

Summary of Contents for AD639R































Reviews:

Related manuals for AD639R