Televes 593395 Instruction Manual Download Page 29

Page: 29 / 31

Error Messages

LOW BATTERY

Indicates that the battery is about to finish. The

battery icon is red now. It is recommended to

connect the meter to the external power source.

LOW BATTERY

Shutting down

Some time after the LOW BATTERY message

appears (time varies depending on the functions

used), it will appear this message. If the meter is

not connected to the external power source, it will

switch off.

BAD POWER

Unplug power source

This message appears when the meter is

connected to an external power source that does

not supply it the right power. Please, use only the

power source provided with the

H30FLEX

SHORT-CIRCUIT

Check installation

This message appears when the meter detects a

short-circuit at the RF input. It is recommended to

check the installation to find out why the short-

circuit is produced.

DC OUTPUT LIMIT EXCEED

Switch DC OUTPUT off

This message appears when the meter detects

an excessive consumption from the device that is

being powered. It is recommended to turn off the

powering feature of the

H30FLEX.

DC AT RF INPUT

Check installation

This message appears when the meter detects

DC at the RF input that is not generated by

the

H30FLEX

. It is recommended to check the

installation.

Maintenance

Always disconnect the unit before cleaning. Use

only a mild solution of detergent and water applied

with a soft damp cloth. Dry thoroughly before use.
Do not use aromatic hydrocarbons or chlorinated

solvents. These products may damage the unit.
Do not use alcohol or alcohol based products

on the front panel, especially the display. These

products may damage the unit.

Summary of Contents for 593395
































Search results

Summary of Contents for 593395

Reviews:

Related manuals for 593395

Brands by name

Popular brands

Televes 593395, Instruction Manual

Search results

Summary of Contents for 593395

Reviews:

Related manuals for 593395

Brands by name

Popular brands