background image

TELES iGATE FCT User’s Guide

12

Previous Page

Table of Contents

Next Page

Programming Summary  

                  

Table 3: DTMF Programming Summary

Code

Function

Remarks

**1343**#

Enter program-
ming mode

To exit programming mode, hang-
up.

*3210*#

Update Immedi-
ate Dialling.  The 
channel will start 
dialling immedi-
ately after 
receiving this 
number of digits

This is followed by the number of 
digits required for Immediate Dial-
ling and then by #.   Enter “0” to 
disable Immediate Dialing.

*3211*#

Update Inter-
digit Timeout

See “Interdigit Timeout” on 
page 15.

*5351*#

Erase Toll 
Restriction table

See “Toll Restriction” on page 19.

*5470*#

Restore Factory 
Default

See “Restore Factory Default” on 
page 18.

*5580*#

Change Rx/Tx 
audio gain

See “Audio Gain” on page 13.

*6100*#

Enable SIM PIN 
code feature

See “PIN Code Programming” on 
page 16.

*6101*#

Disable SIM PIN 
code

See “PIN Code Programming” on 
page 16.

*6110*#

Change SIM PIN 
code

See “PIN Code Programming” on 
page 16.

*6122*#

Clear Channel 
Lock

See “Clearing a Lock” on page 14.

*6133*#

Call Duration 
Limit

See “Call Duration Limit” on 
page 13.

*6150*#

Erase SMS mail-
box

See “Erase SMS Inbox of the SIM 
card” on page 14.

*8200*#

Enable CLIR

See “Calling Line Identification 
Restriction (CLIR)” on page 14.

*8201*#

Disable CLIR

See “Calling Line Identification 
Restriction (CLIR)” on page 14.

*8600*#

Enable Comfort 
Tone

This activates a short beep that is 
played in place of silence.

*8601*#

Disable Comfort 
Tone

This deactivates the comfort tone.

*8620*#

Enable Mod-
ule’s Dial Tone

Creates a dial tone matching that 
heard in the United States

*8621*#

Disable Mod-
ule’s Dial Tone

Disables the US dial tone

*9190*#

Enable Toll 
Restriction

See “Toll Restriction” on page 19.

*9193*#

Disable Toll 
Restriction

See “Toll Restriction” on page 19.

*9194*#

Add entry to Toll 
Restriction table

See “Toll Restriction” on page 19.

*9195*#

Remove entry 
from Toll Restric-
tion table

See “Toll Restriction” on page 19.

Table 3: DTMF Programming Summary

Summary of Contents for iGATE FCT































Reviews: