background image

Page 7

 

Chapter 1  

Introduction 

he Telenetics RM16M Universal Data Shelf™ is a heavy-gauge 
steel-plated modem rack chassis. It measures 7 inches high and 
10.75 inches deep, and mounts in a standard 19- or 23-inch rack. 

The Data Shelf comes in two versions: AC (RM16M ACV-R) and DC 
(RM16M DCV-R). This Guide covers both versions. 

Overview 

The Telenetics RM16M Universal Data Shelf has slots that accept 16: 

Modems  

Multiplexers 

Digital Data Service (DDS) units 

Dial backup units 

Automatic calling units 

All of these devices are plug-in printed circuit (PC) cards that slide 
into the front of the Data Shelf. The cards can be mixed in any way 
within the Data Shelf. Each card has been independently tested and 
meets Part 68, FCC rules and regulations. 

Power, Data Terminal Equipment (DTE), and communication-line 
connections are made at the back panel of the Data Shelf (see “Back 
Panel Interface Connectors” on page 9). This allows PC cards to be 
installed or replaced, without disturbing the cable connections at the 
back 

The AC version of the Data Shelf accepts a single power module that 
occupies two slots, while the DC version accepts two power modules 
that occupy one slot each. The power modules power all the PC cards 

Summary of Contents for RM16M - Versatile Rack Mounting Chassis


















































Reviews: