Teledyne T3PS13206 User Manual Download

Page: 13 / 54

OVERVIEW

Series Lineup / Main Features

Performance



Low noise: Temperature controlled cooling fan



Compact size, light weight

Operation



Constant Voltage / Constant Current operation



Series Tracking / Parallel Tracking operation



Output On/Off control



Multi-output:
T3PS13206: 32V/6A x1;
T3PS23203: 32V/3A x2;
T3PS33203: 32V/3A x2, 5V/5A x 1
T3PS43203: 32V/3A x2, 5V/1A x1,

5V/1A x1



Coarse and fine Voltage/Current control(T3PS13206)



Output voltage compensation control

(T3PS13206)



Function for locking the setting voltage
(CH1/CH2)



Output voltage/ current setting view



Set the displayed digit resolution for the voltage
& current output.

Protection



Overload protection



Reverse polarity protection



Inadvertent voltage setting protection

Interface



Remote control (Output ON/OFF)

Summary of Contents for T3PS13206























































Search results

Summary of Contents for T3PS13206

Reviews:

Related manuals for T3PS13206

Brands by name

Popular brands

Teledyne T3PS13206, User Manual

Search results

Summary of Contents for T3PS13206

Reviews:

Related manuals for T3PS13206

Brands by name

Popular brands