Teledyne T3PS13206 User Manual Download | Manualshive

Page: 30 / 54

background image

T3PSX3200 Series User Manual

30

Switch between Channels

Background /
Connection

This feature is only available for the
T3PS43203.The voltage and current settings and
readback values for 2 channels can be displayed on
the LCD display simultaneously. To check and
view the relevant information for the other
channels, you need to switch channels. Please
follow the steps listed below to switch between
channels.

Panel operation

Press the CH1/4 key to toggle between
CH1 and CH4. The activated channel will
be shown on the channel indicator.

CH1/ CH4

CH2/CH3

①

④

Press the CH2/3 key to toggle between
CH2 and CH3. The activated channel will
be shown on the channel indicator.

CH1/ CH4

CH2/CH3

② ③

«
...
28
29
30
31
32
...
»

Summary of Contents for T3PS13206























































Reviews:

No comments

Related manuals for T3PS13206

Brand: Teccpo Pages: 14

Brand: SafetySpeed Pages: 43

BT-CK 18 2B-1.5 Kit

Brand: Taurus Pages: 40

Brand: Valcom Pages: 2

Brand: Valcom Pages: 5

Brand: Valcom Pages: 5

Brand: Valcom Pages: 3

Brand: Valcom Pages: 3

Brand: National Flooring Equipment Pages: 84

MAG-8200 Series

Brand: Magna-Matic Pages: 38

Brand: Xantrex Pages: 64

Brand: Sealey Pages: 3

Brand: Daitron Pages: 7

Brand: Xinpu Pages: 13

Brand: Far Tools Pages: 46

Brand: Cleco Pages: 16

Brand: Daewoo Pages: 29

NorTronic 43500

Brand: norbar Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands