Teledyne T3PS13206 User Manual Download | Manualshive

Page: 48 / 54

background image

T3PSX3200 Series User Manual

48

F

AQ

Q1. I pressed the panel lock key but the output still turns on/off.

A1. For safety reasons the output key is not affected by the panel key
lock feature.

Q2. The CH3 overload indicator turned on – is this an error?

A2. No, it simply means that the CH3 output current reached the
maximum 5.2A and the operation mode turned from CV (constant
voltage) to CC (constant current). You can continue using the power
supply, although reducing the output load is recommended.

Q3. The specifications do not match the real accuracies.

A3. Make sure that the power supply is powered on for at least 30
minutes, 20°C ~ +30°C.

«
...
46
47
48
49
50
...
»

Summary of Contents for T3PS13206























































Reviews:

No comments

Related manuals for T3PS13206

Brand: Makita Pages: 14

Ultra-Lok UL4000

Brand: Band-it Pages: 14

Brand: Caen Pages: 17

Brand: Parkside Pages: 53

Brand: Parkside Pages: 38

Brand: ?HC Pages: 2

Brand: Placid Industries Pages: 4

Brand: ASG Pages: 10

Brand: TDK-Lambda Pages: 16

GE current Tetra GEPS24-100U-GLX

Brand: Daintree Pages: 3

Ax-Press 25 22 V ACC

Brand: REMS Pages: 168

Brand: Circuit-test Pages: 10

Brand: Scheppach Pages: 192

Brand: West Industries Pages: 13

Brand: Lumina Power Pages: 19

Brand: PTN Pages: 28

Mobile Problast 80017

Brand: Vaniman Pages: 5

Brand: YOKOGAWA Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands