Teledyne PS200 Series Operation & Maintenance Manual Download Page 21 | Manualshive

Page: 21 / 58

Teledyne PS200 Series Operation & Maintenance Manual Download Page 21

PS200

PORTABLE GAS MONITOR

OPERATION

64171, Rev. 11/December 2019

3-1

3. OPERATION

Figure 3-1: Function Buttons

3.1. Operating Procedure

Check the following before use:
• The monitor is clean and in good condition.
• The filters are clean and in good condition.
• The sample line (pumped monitors) and any other accessories used are in good condition and

leak-free.

• The battery is fully charged.
• There are no faults.
• All ranges are operational and the monitor is zeroed.
• The monitor is within the calibration period.

CAUTION: The monitor can be supplied with a flammable gas sensor. This sensor is

designed for use in concentrations of gas not exceeding the Lower

Explosive Limit (LEL). Exposing the sensor to concentrations of

flammable gas above the LEL will not damage the sensor due to an

inbuilt feature. Refer to

Section 4. ALARMS

for details.

NOTE: Throughout this document, the buttons will be referred to as L Button and R Button.

«
...
19
20
21
22
23
...
»

Summary of Contents for PS200 Series



























































Reviews:

No comments