background image

COPYRIGHT 

© 2018 Teledyne CETAC Technologies 

610108 Rev 0 , December, 2018 

Teledyne CETAC Technologies authorizes its 
customers to reproduce, transmit, or store 

this document in its entirety, including this 

page, for the express purpose of installing, 

operating, or maintaining the product 

described herein. 

Teledyne CETAC Technologies 
Customer Service & Support 

14306 Industrial Road 

Omaha, Nebraska 68144, USA 

Phone 

(800) 369-2822 (USA only) 

Phone 

(402) 733-2829  

E-mail 

[email protected] 

REVISIONS 

Teledyne CETAC Technologies strives to 

provide the scientific community with an 

unparalleled combination of effective 

technology and continuing value. Modular 

upgrades for existing instruments will 

continue to be a prime consideration as 
designs progress. 

Teledyne CETAC Technologies reserves the 

right to revise this document and/or improve 

products described herein at any time without 

notice or obligation. 

TRADEMARK ACKNOWLEDGEMENTS 

Windows is a registered trademark of 

Microsoft Corporation in the United States and 

other countries. 

PharMed and Tygon are registered 

trademarks of Saint-Gobain Performance 

Plastics. 

DuPont™ and Viton® are trademarks or 

registered trademarks of E.I. du Pont de 

Nemours and Company. 

Superthane is a registered trademark of 

NewAge Industries, Inc. 

KIMWIPES is a registered trademark and 

KIMTECH SCIENCE is a trademark of 

Kimberly-Clark Worldwide, Inc 

All other marks are the property of their 
respective owners. 

 

 

 

Summary of Contents for SPM-700
























Reviews: